View Full Version : Hydraulic clutch conversion
Limey
08-19-2008, 11:13 AM
Hi guys,has anyone done or got any information on converting from cable to hydraulic clutch actuation?
Thanks in advance
Limey.
LeFox
08-19-2008, 11:22 AM
for what i know, beringer & magura have a setup for buell.
the magura has a possible leak problem at the fitting...(from what i hear)
my techs are in the process of making their own...:o
sinpieces
08-20-2008, 04:20 PM
Yes, buell fanatics has the best so far (they claim).
Also, look at the V-blast exhaust system with the remapped ecm, they sell along for X-tra catshingas ofcourse;
Otherwise Twin motorcycles (Martin & Dris) is releasing one now. They are all pretty expensive. But hey, if you buy one, tell us about it. I think the original -04 clutch ramp works splendid, even though i used to have Müller power clutch before. Yes, before i bought xtra clutch plate kit which is not compatible with Müller.
The Magura i would not buy. It's not without a reason Twin MC is releasing one.
LeFox
08-20-2008, 07:52 PM
Otherwise Twin motorcycles (Martin & Dris) is releasing one now
still in testphase ;)
Limey
08-20-2008, 09:46 PM
Hi guys, I don't want to buy a clutch conversion kit off the shelf,need to make my own. Just one question: when you pull the clutch lever in, does the adjuster(bottom end) on the clutch go in (towards the gearbox?) haven't studied it yet,to busy riding to have a look! Still winters comming (UK)
keep safe all Limey.[cool]
LeFox
08-21-2008, 08:03 AM
don't know what you mean by the adjuster, but the spring is compressed when the lever is pulled in.
so that would mean that the plate is pulled outward.
Limey
08-21-2008, 06:14 PM
That's a shame cos I was hoping that the diaphragm spring was compressed to put the clutch in,which meant that I could use a Kawasaki clutch slave cylinder to press the spring in,(did this on my Rickman & Harris) will have to have a re-think.
Limey
08-24-2008, 06:28 PM
Just found out that Metamachex over here in the UK make a conversion,at a good price,will report back later after some investigation!
LeFox
08-24-2008, 07:38 PM
for the xb or the tuber?
Limey
08-25-2008, 04:56 PM
Don't know,both I suppose but it's a bank holiday today (Monday)so everything is shut til Tuesday.
LeFox
08-25-2008, 05:48 PM
i know metamachex got stuff for the tubers, but don't know of any for the xb range.
jbburf
09-22-2017, 03:40 AM
Did anyone ever do the conversion?
Restlessrustler
09-22-2017, 08:34 AM
I got one for the xb. Need a new line and its good to go....been too busy.
AZmidget91
09-22-2017, 01:34 PM
I have a Magura, apparently there is a new version out now. I'm hoping it corrected the leak issue. Should find out within a month or so when I get the bike up and running.
Nubicon
09-22-2017, 03:13 PM
Why convert the clutch to hydraulic?
Tbone
09-22-2017, 04:52 PM
None of my bikes have hydraulic clutches, but the bikes I have ridden with them are pretty smooth, maybe they have more power than a cable as well?
GregoXB
09-22-2017, 07:41 PM
Why not a Muller power clutch?
pur pony
09-23-2017, 02:27 AM
I hated adjusting cables so I went hydraulic on my tuber. Nice smooth and no adjustments anymore.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.