PDA

View Full Version : Fender eliminator?



paulr
02-05-2010, 10:01 PM
What are my options[confused] for the eliminator kits? I'm getn a stainless d&d slip-on, barend mirrors, K&N filter, have it tuned, and the eliminator kit. I bought this new bike while I was stil payn on my lightning so I'm goin all out with this one. I want this bike to look really nice. Thanks all.

dave_xb12r
02-06-2010, 12:57 AM
I think the jardine fender eliminator kit is the cleanest. http://www.starcycle-usa.com/catalog/46-5001-03.jpg

I've seen ASB's billet fender eliminator. It's very high quality, but it's too damn expensive. The jardine is $100 less than ASBs putting it around $65

paulr
02-06-2010, 01:09 AM
Awesome! I thought all kits were a couple hundred plus so $65 bucks is right up my alley. Got a link to any places that have a good business reputation or should I just google it?

dave_xb12r
02-06-2010, 01:14 AM
You can buy directly from Jardine, or you can get it on amazon. Click here for amazon link (http://www.amazon.com/JARDINE-FENDER-ELIMINATOR-1125R-46-5001-03/dp/B0022YDLM6)

browland
02-06-2010, 01:54 AM
save 60 bucks chop the stock yourself and paint it with spraypaint

Stevenc150
02-06-2010, 02:50 AM
Here's a DIY if you're considering: Fender Chop DIY (http://www.buellxb.com/Buell-XB-Forum/Do-It-Yourself-Buell-Mods/rear-fender-elim-write-up-please.).

paulr
02-06-2010, 04:06 AM
Thanks for postn so fast guys. Just to make sure, this is for my cr right?

paulr
02-06-2010, 04:10 AM
disregard, I didn't read enough.

millenniumx1
02-07-2010, 02:48 AM
I liked the Jardine. Think I got mine from A S B, but not positive. Either way it was about $65, clean install, looks great when done. You'll note in the attached picture that I cut away the under-tail plastic to let the white part of the taillight shine onto the plate. Yes, same kit for the CR as what I used on my '09R.

Mike

http://www.youmarketing.net/100_1057_bw.jpg

Stevenc150
02-07-2010, 04:15 AM
Just to make sure, this is for my cr right?:o It's Dave's fault, I was following his lead. Actaully the concept of the link I posted still applies. ;)

03Firebolt9R
02-07-2010, 01:25 PM
I have the Jardine just like Mikes pictured above and like it alot.

paulr
02-14-2010, 09:19 PM
bought it 20 min ago on amazon. thanks fellas. [up]

RT Performance
02-14-2010, 10:07 PM
Little late but gr harley has them in stock
not sure they have them on there web page
wish I had an extra firebolt plate frame i would jut build the filler panel

paulr
02-14-2010, 11:38 PM
does this kit keep the stock blinkers???

RT Performance
02-15-2010, 12:12 AM
yes

braindead
02-15-2010, 05:46 AM
Will the Jardine fit the xbs

AussieBuellRida
02-16-2010, 03:39 AM
Spewin.. we cant run these in Oz.. cops r all over it. If caught riding with one on, its an automatic defect. Then need to buy a day permit ($40) to ride to the inspection centre, then $120 to have the defect removed... all because they call the rear fender a mud guard... its got a hugger you stupid F@#ks...!!!!![mad]

paulr
02-28-2010, 05:16 AM
Is this new fender hard to put on or is there anything specific I need t know. My instructions are faded and I'm gona try and just figure it out.

paulr
03-03-2010, 05:33 PM
bump

gear2078
03-05-2010, 08:35 PM
Hey Paul, I haven't installed a new tail yet, still trying to design my own. All I can tell you is that I had to pull both seats off and the top plastic off of the tail section to safely unplug two turn signal wires that were too short to get a hold of. Other than that, if you have two hands you can do it.

AZCRrider
03-07-2010, 11:05 PM
Has anyone tried the Evotech fender eliminator? It has the integrated license plate LED. I'm still trying to decide myself.

RT Performance
03-08-2010, 12:56 AM
I made one i used my bolt plate frame and made a filler out of thick plexi glass. Remounted my turns in the plastic of the bolt tail and making a new bracket for it
I also removed the leg for the third bolt so i have some extra space for storage.
No brain it will not work on a xbs completely different tail sections.