Search:

I would be interested in 2 6" and 2 11", all white firebolts. Where can I send the money?

Planning on rolling in late on Friday and staying until Sunday. Looking forward to finally meeting some of you on here

I'll throw my hat in again.http://instagram.com/p/cIXNf8pdbc/#

I would do a multiple stage cleanout. Do the motor flush like you have read, but instead of kerosene, I would just do a lightweight oil like a 0W-20 or something, but DO NOT RIDE IT. I would follow...

I'm with oh9bolt. Recently started a new job, and wasn't able to get the days off

Hey Tifun. I'm over by the old St. Francis. I have probably seen you running around. What do you have?

I just wanted to let everyone on here know that I have opened up my garage as an alternative to going to the stealership. I am on the SE side of Indy, and have posted on here a fair amount. Let me...

Glad your ok! I would agree your GA got their workout. That whole ordeal sounds like it was...ahem...sobering. I hope you are able to get back to the Buells, but respect your position as far as...

Check the front tire air pressure. I got the same thing when I was about 2 pounds low. Other than that, you sound like you have it covered, and the other guys on here have offered some sound advice.

I took mine in shortly after I bought it, thinking the same thing. I was met with an "It's normal." Now, with 20K on the bike, There's no sign of failure, and sometimes she gets temperamental and...

First, Harley guys will, in a LOT of cases, tell you anything to get you out of their face. Mostly, they don't like Buells. As far as a fuse, they would not cause you to have bright lights before...

Unwrap your wire harness in that area, and I would bet you have a number of chafed wires that are shorting to each other. Also, take the flyscreen off, and watch how the harness moves when you move...

I have to say, this weekend was the first time, I had really had an encounter like this. I have had my Buell since '09, and she never got much attention (with me around at least). I had had the...

I would say this is from the seal leaking an pooling in that crack. Since all of the fluid is up above, I would doubt that it is leaking from the bottom. It looks like you have an appointment with...

I haven't had mine on a dyno since it was at about 750 miles. It was only pulling 83RWHP. I can guarantee I am better than that now. I would like to get in on a dyno after the beginning of the...

I have the same and it has been that way since new. I asked the harley guys about it, and they said something to the effect of "it is a pushrod twin, it will be noisy." I would keep an ear out and...

I looked at that but I am not really excited about dropping the fuel pump again. It isnt hard, just a little tedious. In order not to screw up the paint again, I would need to take the bike 100%...

Thank you all for your input. I am leaning toward the Edelbrock 3635 or these out of a Ducati 998. They are mfg'd by Magnetti Marelli and are 46 lb/hr, which might be overkill, but I want to leave...

I have done a fair amount of work on my bike, and if any of you have read Project Valerie, you will see what I mean. To make a long journey a short one, my bike is now a 1250 with a Hawk exhaust and...

+1 on what Tork said. It will filter out all entries unless the log meets certain criteria. I would go on at least a 20 minute ride, then try running it through MLV

I'm running dual D2S HID bulbs in Cadillac housings...I can be seen for 1/2 mile (so the wife told me as I was catching up to her)

When I was at the Motorcycle show in Indy back at the end of winter, I spoke with an EBR rep, and he told me then, that the reveal would be at the Orlando show in October. That might have changed...

Does American Sport Bike in Anaheim work on bikes?

Off the subject, but how do you like the OBX headers? I was looking at a set for my Durango

I was watching Velocity TV, and saw an engine that looked all-too-familiar. MAC Motorcycles is using the Blast engine, and building a new bike on them. I thought you all would love to see it

MAC...