"But IMO, go stock or the mighty 'might-as-wells' can bury you so deep it won't ever see daylight. "
So is stock considered the best bang-for-the-buck setup for power? I'm too old now to spend a...
Type: Posts; User: motoguy
"But IMO, go stock or the mighty 'might-as-wells' can bury you so deep it won't ever see daylight. "
So is stock considered the best bang-for-the-buck setup for power? I'm too old now to spend a...
I cut the tabs off, vinyl wrapped, and put the black mesh piece back on with 3M VHB tape.
Thanks for the info. I have a recently purchased 2010 real wheel I need to assemble (spacers, bearings).
Thanks. Barnett quoted me $107 for a new one a couple of months ago. Not the end of the world.
Perhaps my Google-fu is weak, but I've not been able to find the brackets you speak of. Would you happen to have additional information (pics, part #, source, etc) available for these? The wires on...
Curious, what is the "new" fan logic? I've got ECMDroid and a Buelltooth so I'm sure I could easily program my '06 (has comfort kit) to this logic...if I knew what it was!
Also, having the fan...
Random question...would a Harley lever fit in a Buell mount, thereby allowing use of HD cables instead of (increasingly hard to find / expensive) Buell cables? Possibly a stupid question. I have 0...
Cooter, I notice you didn't remove your rear wheel during the fuel pump exchange. I removed mine because I was concerned of damaging the belt at full extension when I removed the shock. If I can do...
I used the Aagaard video posted here:
https://www.youtube.com/watch?v=wdRLwDRlqhA&t=2529s
It doesn't help with removal (there are other videos on that), but it does help with the rebuild. Once...
If I want to buy a kit to do Buell wheel bearings, what's a good one to buy? I see lots of wheel bearing pullers on Amazon, and notice there are some specifically listed as "HD" units. Do I need...
I'd recommend picking up a small roll / bit of cable wrap as well. My '06 didn't have any and there were a couple of abrasion marks on my wires. The later bikes (08?) had it installed from the...
Good info. I'll check the bolts on my bike as well. On the '06 the kickstand is a bit "floppy".
Still has to be better than the God-awful kickstand my Guzzi 1100 Sport had!
My recently purchased '09 Uly has the comfort kit but the rear shock cover is broken. I may try to plastic weld it together as a spare, but I found one on eBay from a bike being parted. My bike has...
Rebuilding my pump on my '07 today, I noticed a couple of tiny nicks in the wiring as shown in some of the photos in this post. I also noticed the wires do not have the protective sheath like other...
Bringing one back from the dead, I know. I pulled the fuel pump from my '07 Uly today, planning on rebuilding it with the kit purchased from Revision Moto. Upon laying out all the parts, I realized...
Thanks for that info. I’ll do so. Any other parts from the 07 engine that should stay on the 07? I planned to do a full “drop and swap” with the engine, intake, etc. I plan on ordering another...
I noticed the '09 XB12R has 8 piston front caliper, but the 09 Uly (early 09, Jan/Feb build) has a 6 pot front caliper. I thought all the '09 bikes would have the 8 pot caliper.
I bought a pair of Ulysses a while back. A runner '06 (40k miles) and an '07 with a bad crank. Both are clean. I've been riding the '06 until the fuel pump went out. Parts are here but I haven't...
Is a full wiring harness swap required? '07 is a Uly, 08 is an XB12R...so different components (ECM etc) in different locations. I suspect the answer is "technically no, but swapping will still be...
Disregard
Well, just punch me in the face! Thanks. Overlooked that.
I ordered one of the inspection cameras. I decided to go with a dedicated unit instead of the "plug it into you phone" type. We'll see...
Thank you!
Suggestions on cross reference for PCV valve on '06 Ulysses? There was a cross reference listed in another thread, but the post has been edited and the cross reference is gone. It was for a VW car,...
'08 is salvage, so I'll be using my existing frame. But I see what you're getting at.
How different are the swingarms? Donor bike is '08 12R...shorter swingarm than Uly, correct? '08...
Thanks for the warning! In that case, what would be the best way to get potential water buildup out of the crank case? I'm not certain there is any in it...but I'm also not certain there isn't.