Search:

Type: Posts; User: s0dhi

Page 1 of 19 1 2 3 4

Search: Search took 0.15 seconds.

  1. I tried to remove it, but stripped the screw head...

    I tried to remove it, but stripped the screw head - God knows what supernatural thread locker was used. I used an aerosol sensor cleaner and thoroughly cleaned it before jumpering it. I'll order a...
  2. Thread: Ontario Buellers

    by s0dhi
    Replies
    12
    Views
    7,338

    Anyone still out there? In Brampton, ON. ...

    Anyone still out there?

    In Brampton, ON.

    Shout out if you want to meet up.
  3. Replies
    8
    Views
    1,803

    No, there is a precut buckle guard. Give them a...

    No, there is a precut buckle guard. Give them a call. I think it was approx $20-25.
  4. Replies
    8
    Views
    1,803

    +1 for the Techspec grips. I have the buckle,...

    +1 for the Techspec grips. I have the buckle, airbox and frame grips.
  5. Yes, I did with a propane torch and didn't notice...

    Yes, I did with a propane torch and didn't notice any change to the idle. I'm also not sure if the IAC would compensate for it or not.

    Over the winter, I'm going to rotate the engine to either...
  6. OK, the ECM doesn't like the switch disabled. I...

    OK, the ECM doesn't like the switch disabled. I think I would have to turn off those trouble codes within the ECM - kind of like putting electrical tape over a check engine light. I've enabled the...
  7. Replies
    33
    Views
    5,875

    Great work, Jesse! Looks fantastic!

    Great work, Jesse!

    Looks fantastic!
  8. It is supposed to bump idle up 200rpm or so in...

    It is supposed to bump idle up 200rpm or so in gear with the clutch lever pulled on 2008+ XBs. It is by design to keep the bikes from stalling, and to roll away from a stop more easily.

    Found...
  9. So after wrestling with it - the timesert fiasco...

    So after wrestling with it - the timesert fiasco which required additional grinding and swapping the standard ramp for the Muller Power Ramp, the culprit is the clutch switch. I jumped it with a...
  10. Agreed. I haven't ridden the bike since I...

    Agreed. I haven't ridden the bike since I noticed the problem and even then no more than 40 miles were in that state. I'll have it sorted out today, hopefully. Timesert for the clutch cover, then...
  11. Cooter, I've been adjusting it using the process...

    Cooter, I've been adjusting it using the process in the manual - loosening the cable, adjusting the primary and setting the cable.

    Perhaps you can clarify the following:

    Using a flat tip...
  12. I think I have it figured out. It's a...

    I think I have it figured out.

    It's a combination of the Muller Power Clutch, factory clutch lever and my fat gloved fingers. I did not have this issue with the Chinese levers and the Muller...
  13. Neutral light is solid nothing interesting...

    Neutral light is solid nothing interesting happening.

    IAC was super tight but I removed it and cleaned both it and the housing. It took a few Q-tips soaked in cleaner to clean it up thoroughly. ...
  14. Thanks for direction, I will definitely check...

    Thanks for direction, I will definitely check those 2 points out.

    What I find odd is that it idles fine in neutral and only when it's put in gear, with the clutch pulled, do the revs climb up.
  15. Idle climbs in gear with clutch pulled?! Idle stable in neutral, however.

    So this one has me completely baffled.

    When in neutral the bike idles perfectly; however, in gear with the clutch pulled, the idle climbs to 1400-1800 rpm.

    The bike is a 2009 XB9SX. Has a...
  16. Replies
    14
    Views
    8,125

    I have the same issue up here. Still on BUEZD...

    I have the same issue up here. Still on BUEZD wanting to move to BUE2D.
  17. Replies
    31
    Views
    5,903

    Sadly, yes.

    Sadly, yes.
  18. Replies
    59
    Views
    6,831

    lmao.

    lmao.
  19. Replies
    31
    Views
    5,903

    Update: It appears the custom lever I purchased...

    Update: It appears the custom lever I purchased for the ZTL2 was preloading the master and as a result the feel was diminished from the ZTL experience. I've swapped back to the factory levers and...
  20. Replies
    31
    Views
    5,903

    Thanks, Jesse! :up: To be honest, I don't...

    Thanks, Jesse! :up:



    To be honest, I don't know if that's much of an improvement with the standard style master cylinder. I think I'm going to try a radial master cylinder next season and add...
  21. Replies
    31
    Views
    5,903

    New updates to the Buell

    Latest updates:


    white plastics
    APH Reverso exhaust
    ZTL2 brake upgrade


    https://dl.dropboxusercontent.com/u/28846604/DSC_0034.JPG...
  22. Replies
    33
    Views
    5,875

    Great work!

    Great work!
  23. Replies
    59
    Views
    6,831

    Agreed.

    Agreed.
  24. Replies
    35
    Views
    5,498

    Here I am updating a post I made 2 years ago with...

    Here I am updating a post I made 2 years ago with new relevant tuning info, all while Ren & Stimpy videos are being posted. Something's not right.
  25. Replies
    40
    Views
    11,973

    I think adding the load point of 6 was a waste...

    I think adding the load point of 6 was a waste based on reviewing the scatter plots. I think that row is better suited to 45 or 70 where the value is actually getting hit and can provide more detail...
Results 1 to 25 of 462
Page 1 of 19 1 2 3 4