Search:

Type: Posts; User: XB12Steve

Page 1 of 3 1 2 3

Search: Search took 0.13 seconds.

  1. Replies
    23
    Views
    1,962

    So what all has to come off to do drive gear? ...

    So what all has to come off to do drive gear? Rocker box cover then rockers? Can push rod tubes stay in place?
  2. Replies
    4
    Views
    749

    Tps reset, is 3.4 at 1100 rpms ok?

    I keep following the procedure.. keep getting same results. Before I thought it was due to the intake leak.. but now that is 100% fixed with the flange upgrade. Tested and confirmed after to make...
  3. Replies
    23
    Views
    1,962

    So that's what you guys think about my 04 with...

    So that's what you guys think about my 04 with 42k miles on it? I've never inspected the oil drive gear.. have always known it "could" be an issue. I wanna know how many ever had the drive gear...
  4. Replies
    13
    Views
    2,147

    Flanges solved my problem. I did have to take a...

    Flanges solved my problem. I did have to take a 80 grit sand wheel, not a drum, on my dremel to the bores in order for the flanges to fit the manifold. Once I did that a few times they slid on...
  5. Replies
    55
    Views
    9,486

    How much are these gonna run? Rough estimate an...

    How much are these gonna run? Rough estimate an don't say oh Idk. You got to have an idea of how much they'll be
  6. Replies
    13
    Views
    2,147

    If anything I'll use sealant on the manifold...

    If anything I'll use sealant on the manifold itself to seal against the o ring if I have to
  7. Replies
    13
    Views
    2,147

    Used the james with hylomar. Installed coil...

    Used the james with hylomar. Installed coil bracket bolt, not snug but just to hold the alignment then made sure seals were centered an snugged bolts a lil at a time evenly. Flanges are correct...
  8. Replies
    13
    Views
    2,147

    I'm not arguing about anything. I just hardly...

    I'm not arguing about anything. I just hardly can see how the throttle body is the issue. More like the junk design overall is the real issue.
  9. Replies
    13
    Views
    2,147

    How is the entire intake the problem? The...

    How is the entire intake the problem? The barrels are round an not oval.. so explain yourself
  10. Replies
    13
    Views
    2,147

    Intake sealing, the final solution

    I can't for the life of me get these intake seals to actually seal. At this point I've come to the conclusion the flanges are warped. Trust me I've tried everything. Grease, silicone, I've been...
  11. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    With the James intake seals do the flanges still...

    With the James intake seals do the flanges still get tightened down to the cylinders? How do you guys do yours? I ordered new seals and when I go to tackle it I'll use your advice
  12. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    I'll tell you what right now, I've done the...

    I'll tell you what right now, I've done the intake before the top end gasket set before. With the James gaskets I found you literally can't tighten them for them to seal. I barely tightened the...
  13. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    Because I wanted a better answer than just clean...

    Because I wanted a better answer than just clean it.. no **** I already did that. And used a skim coat of grease. Still leaked.
  14. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    I'm not taking that chance. Type 2 is used for...

    I'm not taking that chance. Type 2 is used for flange type seals and is resistant to fuel and heat. I'm dropping this motor for the last time.. thankfully all the more hard to replace gaskets...
  15. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    On second thought we have versa chem type 2...

    On second thought we have versa chem type 2 sealant here at work, it's a non curing joint sealant. Gonna use that. Basically the same as that hylomar blue.
  16. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    I'm gonna use some anaerobic sealer on the faces...

    I'm gonna use some anaerobic sealer on the faces I think. Stuff works very well on everything I've used it on
  17. Thread: Intake seals

    by XB12Steve
    Replies
    12
    Views
    2,074

    Intake seals

    How do you get this piece of **** design to seal? Just got my motor back together from top end gasket replacement along with new stator and VR. Charges correctly now but these junk intake seals are...
  18. Replies
    12
    Views
    1,552

    I want my spare bottom end 34 😏😂

    I want my spare bottom end 34 😏😂
  19. Ok keep us posted. I just bought one for 200...

    Ok keep us posted. I just bought one for 200 beans from harley.. it hurt me emotionally 😏😂😂😂
  20. How much are these gonna run $

    How much are these gonna run $
  21. Replies
    55
    Views
    9,486

    I've got one to experiment on

    I've got one to experiment on
  22. Replies
    12
    Views
    5,093

    I called my local dealer they're 50 cents a pop. ...

    I called my local dealer they're 50 cents a pop. Cheap insurance I suppose
  23. Replies
    12
    Views
    5,093

    Alright 34 I'll order new stator bolts. How much...

    Alright 34 I'll order new stator bolts. How much for your stator? How many miles on it?
  24. Replies
    12
    Views
    5,093

    Lmao. Why would the bolts break it's a...

    Lmao. Why would the bolts break it's a stationary part? Snug with loctite will be more than sufficient. I doubt they need 200 lb ft of torque applied to them
  25. Replies
    12
    Views
    5,093

    Yeah I'd just loctite old bolts an run it

    Yeah I'd just loctite old bolts an run it
Results 1 to 25 of 75
Page 1 of 3 1 2 3