hi I'm not sure if this goes here, but I have the EBR ECM for sale. It is paired with a drummer exhaust and it is from an 09 XB12SS. Make an offer if you are interested.
Type: Posts; User: lrholy06
hi I'm not sure if this goes here, but I have the EBR ECM for sale. It is paired with a drummer exhaust and it is from an 09 XB12SS. Make an offer if you are interested.
I live in Utah where its cold during the winter and for the past three years have hauled the bikes over to Cali to do some Winter riding. Last trip, as I was quite excited to be there, I wasnt...
I have one for an 09 XB12ss. I dont know if they are compatible or not. Whats the problem?
http://www.buellxb.com/buell_images/6154_20130309103623_L.jpg
Should that be spinning across the pick up coil as I try to start it? It turns freely like you said it should but it does not snap back into place.
Ok I'll pull that off and see. Any idea what the out put should be?
Hey everybody,
I hope I am posting this in the right spot. I pulled a 1979 Honda 185 XLS out of a barn here on the property. It has sat there for more than 20 years. The last time it was...
I have managed to convince a neighbor guy here to come along with me to California to do some riding. We are both from Utah and want to ride in some warmer weather. Can somebody suggest some good...
Ok, so i did the TPS reset, I pulled the air filter base off and adjusted all the hoses to make sure that one of them was not getting kinked and put it back together. It seemed to run fine in the...
So it will run but only with the air box off. I pulled the cover off, and the shell with the interactive exhaust cable to get to the filter. I just cleaned and re-oiled the K&N filter. It would...
yes, the gauges sweep just fine and the check engine light is NOT on thank goodness. I was very suprised at that after having the engine open for over 5 months. So would the gas I used to get to...
Well I got it started and went about a half of a mile and it died on me. It will crank and turn over bit then just die after a second. Anybody know what I can try now?
I got it! Sweet! It was the upper engine tie bar. I guess it has to be grounded or the bike wont start. Thanks for everything guys. I wouldnt be able to do this without all the help!
So now I get a really rapid clicking noise when I tried to start it. What is that supposed to mean?
The engine was originally rotated because of a broken header stud. I had to remove the engine head and have somebody drill it out. (Its a long story and it took about five months to finally get it...
I was leaving as much stuff disconnected as I could because I was worried about getting everything back together and then something not working and having to disconnect everything again and rotate...
yes its in neutral. I mean the neutral light is on. I will take it off the stands and check for sure. I also have the clutch cable currently disconnected, would that stop it from starting??
Lunaticfringe, you will have to forgive me but I am not too familiar with some of the terminology. What do you mean by "hydraulic the motor"? and by "Spin it over" do you mean try to start it?
the short story is now that I have everything back together after a five month engine rotation, the bike wont start.
The battery is good, lights are bright, I checked the fuses and all of them were...
nope, no welding. I was able to drill down to the cobalt but its not quite far enough to re thread it. I just should have trusted you guys and told my father that we were just going to drill and...
why does it seem that every project that this stupid bike needs turns out to be a 4 month catastrophe?
I had a header stud break back in september. One bolt. Thats it. Of course it broke off flush...
Can anybody tell me if I can use Harley Evo Sportster gaskets in an SS? The ones on americansportbike are 40 dollars and the ones from harley are less than ten. Are they made of different...
Mine was doing something really similar a few weeks ago and I started searching for a ground/bare wire or anything that might look suspect. I couldnt find anything until I noticed that my battery...
Awesome! I did it. If you had told me even a few weeks ago that I would be rotating an engine out I would have just laughed at you. Thanks for everybody's help here, Sure could not have done it...
Well sorry to bring this back up but does anybody have a write up to remove the frame?
I removed the headers without the engine rotation but then messed up while drilling. It looks like I have to...