Search:

Type: Posts; User: Endopotential

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    679

    So cool! I'm going to get to do my first track...

    So cool! I'm going to get to do my first track day ever at Thunderhill Sept 8. Can't wait!
  2. Replies
    2
    Views
    138

    Gotta ask why it was a salvage title. These...

    Gotta ask why it was a salvage title. These bikes don't have any big expensive fairings to crack. So no dents on the frame or exhaust pipe? Check the tabs on the steerer tube - a bend here...
  3. I had to remove my rear wheel recently without...

    I had to remove my rear wheel recently without the official Buell tool.. You definitely have to get creative.

    So to clarify those pictures above - either find yourself a long 7/8" coupling nut,...
  4. Replies
    24
    Views
    831

    After doing the above, consider getting the...

    After doing the above, consider getting the Buelltooth diagnostic tool to plug into your ECM.

    You can then check if the bike has the correct on/off temperature parameters for the fan, and also do...
  5. Replies
    312
    Views
    134,665

    Yeah, drooling over that photo was what started...

    Yeah, drooling over that photo was what started this whole adventure! :eagerness:

    Don't know how I'll ever be able to keep the bike as sparkling as you did. There's a lot of shiny metal on that...
  6. Replies
    18
    Views
    804

    Are you getting any CEL's? Do you have...

    Are you getting any CEL's? Do you have Buelltooth to get an error codes? Or jump the wire the old fashioned way?

    Here are some guesses - Bike running too hot? Can you measure cylinder temps? ...
  7. Replies
    312
    Views
    134,665

    Just to close the chapter on Nick's wonderful...

    Just to close the chapter on Nick's wonderful creation.

    It finally made its way to Northern California. Turned out to be a bit of a hassle getting it registered here. It's such a unique build...
  8. Replies
    11
    Views
    406

    What exactly are we looking at? Is that the O2...

    What exactly are we looking at? Is that the O2 sensor from the top down? If it's on the right side of the bike, there's always the danger of it getting caught in the belt drive which could do...
  9. Dang, Cooter. Your "10 minute job" was more like...

    Dang, Cooter. Your "10 minute job" was more like a 3 hour ordeal for me. Mostly because I didn't realize you could drop the swingarm far enough without removing the rear wheel. Which meant...
  10. I had similar problems with hard starting on a...

    I had similar problems with hard starting on a cold engine. Turns out it was a hole in the supply flex hose within the fuel pump assembly.
    ...
  11. Turns out I was premature in my celebration. It...

    Turns out I was premature in my celebration. It wasn't the IAC after all. Bike was still hard to start afterwards.

    I bit the bullet and replaced the fuel pump parts, thanks to...
  12. Replies
    19
    Views
    3,573

    But if someone cut off that sidestand switch and...

    But if someone cut off that sidestand switch and wired it up higher, where does it ultimately lead to? Somewhere up by the handlebar, or towards the ECU in the back?
  13. Replies
    19
    Views
    3,573

    I'm getting a "sidestand input always high" error...

    I'm getting a "sidestand input always high" error code off my ECM Droid.

    I can't find any wires down by my sidestand. Could anyone tell me where those wires would lead to? Pics would be really...
  14. WOOHOO!!! Solved for the most part I think. ...

    WOOHOO!!! Solved for the most part I think.

    The prize goes to njloco. Thank you sir! I owe you a virtual beer.

    I took out the IAC (idle air control) under the airbox. It wasn't filthy or...
  15. @ocgreenmachine. Thanks, that's really helpful...

    @ocgreenmachine. Thanks, that's really helpful to know. How in the world did your ever diagnose those tiny pinholes?

    I've had the sinking suspicion that I would need to replace the fuel pump,...
  16. I've tried keying the run switch several times...

    I've tried keying the run switch several times before hitting the starter, thinking about that priming issue, but to no avail.

    I was able to get into the basics with ECM Droid. The map that was...
  17. Thanks guys for chiming in. Will try to work on...

    Thanks guys for chiming in.
    Will try to work on the ECM mapping over the next couple days. But that should only affect running, not initial startup no? Unless the map is really screwed up for low...
  18. Another hard start issue - SOLVED! It's the IAC Idle Air Control

    I've got an '09 XB9SX, 20k miles, stock exhaust, stock ECM. Just got a Buelltooth and trying to figure out if I have a stock map. TPS reset done. Ever since I got the bike last year / 1000 miles...
  19. Replies
    28
    Views
    2,504

    Here are some pics of the bike at its new home. ...

    Here are some pics of the bike at its new home. A beautiful bike deserves a nice backdrop. Riding the coastal Hwy 1 just outside of Pacifica, by SF.

    11945

    11946
  20. Replies
    28
    Views
    2,504

    That's awesome Nick! I was afraid you were going...

    That's awesome Nick! I was afraid you were going to get away from motorcycles altogether.
    A high revving Italian would be about the diametric opposite of our grumbling lumps!
  21. Please do fill me in! I've got a Firebolt XB12R...

    Please do fill me in! I've got a Firebolt XB12R (well, actually nicholas900's heavily modified cafe racer version...). I'm guessing the XB9R has the same frame?

    Are Firebolt frames different...
  22. WANTED: XB Frame pucks, headlight grill

    Any chance one of you has parts off of an old XB or Firebolt?

    I'm located in San Francisco, CA. Thanks!
  23. Replies
    28
    Views
    2,504

    I'm happy to say that I'm now the proud new owner...

    I'm happy to say that I'm now the proud new owner of Nick's incredible creation. It made a long journey from Buffalo, NY to San Francisco.
    Pictures fail to do this bike justice - the build quality...
  24. Replies
    28
    Views
    2,504

    I realize I'm way late in finding this thread,...

    I realize I'm way late in finding this thread, but any chance it's still available? Would love to buy it from you. Please send me a PM
  25. Replies
    31
    Views
    1,638

    I'd be interested in handguards, headlight grill...

    I'd be interested in handguards, headlight grill cover, and rear passenger pegs. Could you email me pics? Thanks!
Results 1 to 25 of 43
Page 1 of 2 1 2