Search:

Type: Posts; User: dodge

Page 1 of 5 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    6
    Views
    231

    You're the bomb me. Once the rain stops, I'll go...

    You're the bomb me. Once the rain stops, I'll go check things out.
  2. Replies
    6
    Views
    231

    Code 43....my rigged wiring may be at fault me...

    Code 43....my rigged wiring may be at fault me thinks. There were 2 R/w stripe wires I removed from the ecu connection plug...might have gotten these crossed up. Is there a fuse for the speedo? It...
  3. Replies
    6
    Views
    231

    I think it was 34...speed sensor short?

    I think it was 34...speed sensor short?
  4. Replies
    6
    Views
    231

    Speedometer woes...

    Died. CEL comes on after 3-5' of driving. Replaced the speed sensor today. Still dead. It was a HD sensor that was not a direct replacement...came with the wiring harness and connector which I had to...
  5. Replies
    4
    Views
    1,101

    Trying to tackle this once again.. Got the 08...

    Trying to tackle this once again.. Got the 08 working fine with the baro sensor using ecmspy mono. Trying to do same with the 07, but there are greyed out areas in the 07 settings via mono. The...
  6. Anyone familiar with the HD ver of Megalogviewer?

    Had used the older version years ago, but this senior seems to have forgotten some of the initial settings etc. Using ECMDroid to log MSL files and burn the new tables etc in. Using TunerProRT as...
  7. Replies
    4
    Views
    1,101

    Yeah, was able to set it up using the latest ver...

    Yeah, was able to set it up using the latest ver of ESpy on my 08 and verified it is working by applying either pressure or vacuum to the sensor. But, cant seem to get it up and working on the 07....
  8. Replies
    4
    Views
    1,101

    baro sensor enabled eeprom?

    Anybody have a baro sensor enabled eeprom for the BUEID (2007 XB12S) firmware?
  9. Thread: Tires

    by dodge
    Replies
    9
    Views
    839

    Shinkos

    Shinkos
  10. Replies
    6
    Views
    1,376

    Hey tok-I used the latest version of MLV to remap...

    Hey tok-I used the latest version of MLV to remap tables on both my 07 XB12 and stock 08 XB9SX. Used NTK's latest AFRM wideband sensor and controller. Used ECMDroid to log the data using a 7"tablet...
  11. Replies
    2
    Views
    595

    File format issue or perhaps ecm firmware...

    File format issue or perhaps ecm firmware mis-match?
  12. ERROR: Failed to fetch ecm type: Cable Problem (RX/TX Shorted?)

    Getting this msg when trying to connect using ESpy with either cable or BT module. Bike starts up fine and runs...but cant "talk" with it. What happened??

    update: So I got out this evening and...
  13. Replies
    3
    Views
    805

    Back in the saddle!! yea..

    Back in the saddle!!

    yea..
  14. Replies
    3
    Views
    805

    Hey gunter-thanks for responding! Reinstalled...

    Hey gunter-thanks for responding! Reinstalled everything once again only this time went ahead and filled out the activation form and sent it in. Only did not make a donation a second time. Not sure...
  15. Replies
    3
    Views
    805

    Post reinstall of ECMSpy Mono issue..

    Had to do a Win 10 reset on the Dell laptop. Had a new activation password made and have reinstalled all the needed apps-MONO app, EcmSpy Mono program and the BUE2D database file. Generated a new...
  16. Replies
    3
    Views
    572

    https://www.youtube.com/edit?o=U&video_id=zK7ZNstT...

    https://www.youtube.com/edit?o=U&video_id=zK7ZNstTnys
  17. Just recently completed a re-map of a stock 08...

    Just recently completed a re-map of a stock 08 XB9SX. Used TunerPro RT to enable/disable options and to modify rpm and tps load axis tables. Used EcmDroid to log data and Megalogviewer HD to create...
  18. Replies
    18
    Views
    2,199

    Thanks-well on the way to doing both. MLV is...

    Thanks-well on the way to doing both. MLV is doing exactly what it's supposed to do. Just needed to tweak the curve a tad.
  19. Replies
    18
    Views
    2,199

    Well, it does seem to idle better with a bit more...

    Well, it does seem to idle better with a bit more fuel. Bike seems smoother etc. with an increase in fuel across the board. Don't think it would pass emissions though..
  20. Replies
    18
    Views
    2,199

    The curve is required for MLV to create the new...

    The curve is required for MLV to create the new fuel tables. Oh no, 16:1 just to see what the wideband controller/gauge output is at that afr to create that curve. Its much happier at 13:6 or so at...
  21. Replies
    18
    Views
    2,199

    Update..finally seeing some usable Voltage data...

    Update..finally seeing some usable Voltage data when the NTK wb gauge is connected to pin #32. Now making a really custom linear curve for MLV to chew on. Idles at 13.7:1 and 1.57V. Need to reduce...
  22. Replies
    18
    Views
    2,199

    Odd, but didnt have this issue with an older ver...

    Odd, but didnt have this issue with an older ver of spy, MLV and the 07 (BUEID) bike. Think I'll try tying into a pigtail at pin 32. Thats the way I logged data on the 07. Upside to all this is I'm...
  23. Replies
    18
    Views
    2,199

    OK-small update.. The dual wideband sensors...

    OK-small update..

    The dual wideband sensors are connected to ecm via pigtails at pins 1 and 33. Sensors are set to output their 0-4.096 volts. Connect the running bike to ecmpspy and then enable...
  24. Replies
    18
    Views
    2,199

    MLV option field settings?

    Curious what folks are choosing for the EGO and AFR field options for the veAnalize procedure. I'm not seeing any 0-5V data in the log replays. Something aint right...
    Thanks!
  25. Replies
    18
    Views
    2,199

    We talking the various options for the EGO and...

    We talking the various options for the EGO and AFR fields? Tried most of them...getting wild numbers. Using the lastest (MLV HD) ver of MlV.
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4