Search:

Pretty sure my 07 has scissored the crank (havent torn it apart yet) but I seen somewhere that the 08 has a stronger crankpin than the 07's.

Does anyone know about this swap and or where I might...

My 04 9R did this years ago. I was deployed to Iraq for 12 months and my wife at the time would go and start the bike once or twice a month and let it run till the fans came on. About 10 months of...

Got the bike back. Runs good, could still use some fine tuning for the street.

Gb, PM me an email and i will send you the maps and data log from today. I am interested in what you see with the...

Supposed to go down to get the bike this afternoon. Eric, did you happen to get those screen shots? Gb, any other ideas?

So interesting day on the dyno today.....

We figured out that at about 202c and 4-5k rpm the bike is dropping the O2 voltage(no idea why). We can duplicate the issue over and over (sensor is brand...

Eric,

Did you get anywhere with the screen shots?

cjmech #4

That would be great.

During the tuning process this has been disabled. Once the tune was set it was re-enabled.... Leaving it disabled wont cause any issues?

What does the open loop...

In the ECM config tab it has the open loop learn enable selection. This is what I believed to enable/disable the learn functions..

The tuners computer has any logs that were saved. I have megalog...

Using ECMSPY.

I should have asked if you can leave it turned off rather then just during the tuning process.

I know you turn the open loop learn function off for the tuning process. But if...

The EGO Correction % is the number I believe he was talking about.

Is there a way to shut this off all together?

The bike runs like an animal all the way up until this voltage signal issue...

So today I got a new 02 sensor and installed it. We put it back on the dyno, Had the same problem... so...... We copied the stock closed loop area and pasted it into the tuned map and re-ran it. This...

cjmech #3

gbalias,

Your inbox is full....

Yes, clicked the reset and she fired right up and idled. The AFV was at 100.

The bike is an 07.

I get that it wouldn't throw the code if it was getting...

Took the bike back to the tuner yesterday, checked fuel pressure (49-50 psi) went into ecmspy and reset the AFV to 100 and the front cylinder came back...

Put it back on the dyno today and just...

cjmech entry #2

Definitely need to get put down for this. cjmech #1

Ok, so I got a new used coil and wires today. Checked the resistance on the wires and made a set with the lowest resistance in them. Still not running on both cylinders... I pulled the intake off and...

Once the bike was off the dyno I downloaded the map from the ecu and saved it.
When I came off the track I downloaded the map and compared it to the saved map just to see if anything was different....

Yes.

Please dont think that I am unappreciative in any way, I apologize if that's how I cam across. After all I am here looking for outside input.

In looking at the values of the factory...

No I havent rulled that out yet. But also why I am looking for information on how to check it. A new one is almost $170....

This is the only post that bothered me honestly. Most of the others were irrelevent.

I spent about 5 hours on the dyno tweaking the fuel and ignition maps along with the guys there running the...

Well after doing a compression test on the bike I found that its not a valve issue. I checked the resistance on the plug wires and coil which all test fine.

Anyone know how to test the CPS?
...

Love how you guys on here miss the point of the post every time... my question was about where to find the parts and what vendor might have the best ones to use in these engines.

I didn't ask for...

Had the bike tuned Friday, hit the track yesterday and got 5 laps and she was done..... Whole lot of money for nothing and now I have to tear it apart again after just rebuilding it a few months ago....