Search:

Type: Posts; User: cocoabutterlover

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    11
    Views
    602

    Try to pick up some Plexus Plastic Cleaner. I use...

    Try to pick up some Plexus Plastic Cleaner. I use it to clean my helmet and visor, it leaves a nice oily film so the next time you clean off your parts, it comes off easier.
  2. Replies
    15
    Views
    475

    Did the originals leak because of an install...

    Did the originals leak because of an install issue?

    Since they weren't in there long before they started weeping, were they maybe not oiled at install? Are they supposed to be oiled at install?
    ...
  3. Replies
    8
    Views
    619

    Its super easy to test your stator. Almost dumb...

    Its super easy to test your stator. Almost dumb that's how easy it is. Start there.
  4. Replies
    6
    Views
    462

    I have a question lined up. Where's you get that...

    I have a question lined up. Where's you get that assembly blow out?
  5. I'll put it this way. I picked up a 2008 xb12ss...

    I'll put it this way. I picked up a 2008 xb12ss long with 72000km three months ago; my first Buell, but not the first one I've ridden. Has issues. I put in work since I bought it. Still has issues....
  6. Replies
    6
    Views
    451

    if you look closer at mine it's skulls. Previous...

    if you look closer at mine it's skulls. Previous owner's taste not mine. I just bought the Buell Decals for it.
  7. Replies
    6
    Views
    451

    His original was black so depends on what you...

    His original was black so depends on what you look. Personally, I would not have done this. It's not a wrap but a hydro dip thing.
  8. Replies
    40
    Views
    1,844

    New TPS arriving today; hopefully they leave it...

    New TPS arriving today; hopefully they leave it at my door. Along with a right side air scoop.

    Will update once new TPS is in.
  9. Replies
    22
    Views
    1,402

    Any idea what voltage your TPS runs at?

    Any idea what voltage your TPS runs at?
  10. Replies
    35
    Views
    2,647

    whats the part # on the cooling fan? How much for...

    whats the part # on the cooling fan? How much for it? PM me.

    May be interested in front and rear brakes in you can check that they're not warped. and possibly give me thickness size as I can't...
  11. Replies
    19
    Views
    3,897

    Sidestand switch.

    Sidestand switch.
  12. Well for some feedback; I installed new intake...

    Well for some feedback; I installed new intake seals; bike ran funny. I took apart my TPS and cleaned it, re-installed it, ran extra ground wires. Took the bike out last night, it ran smoother while...
  13. I went with two 10 gauge wires. Bike seems to run...

    I went with two 10 gauge wires. Bike seems to run ok.
  14. Perfect. I was wondering if that will work. I...

    Perfect. I was wondering if that will work. I will try it out since I have a coil of 12 gauge at home. Thank you. May not fix issues but it'll help with peace of mind.
  15. Am I wasting my time running a 12 gauge wire from...

    Am I wasting my time running a 12 gauge wire from braided strap to battery negative terminal? Or does it need to be 4 gauge? I want to try this out. But asking ahead of time.
  16. Replies
    40
    Views
    1,844

    4.13 Kohm across power to ground 4.65 Kohm...

    4.13 Kohm across power to ground
    4.65 Kohm across power and return (throttle closed)
    1753 ohm across power and return (throttle full open)
    4.77Kohm when returned back to closed.

    When I took it...
  17. Replies
    40
    Views
    1,844

    Final pictures of the intake seal job. I did...

    Final pictures of the intake seal job.

    I did grease up the new seals when installing.

    After the initial test ride I noticed that the bike still didn't run 100%.
    Error code came back again for...
  18. Replies
    40
    Views
    1,844

    Part 2 The ratchet with pivoting head in the...

    Part 2


    The ratchet with pivoting head in the last photo helped a lot. Eliminated the need for a stubby wrench.

    Also, that bolt that attaches to the coil igniter bracket and the throttle body...
  19. Replies
    40
    Views
    1,844

    So I finally picked up new intake seals. ...

    So I finally picked up new intake seals.

    Here's what the previous owner had done.
  20. Replies
    40
    Views
    1,844

    So I finally got to spray some carb cleaner into...

    So I finally got to spray some carb cleaner into my intake seals. The very first spray the RPM climbed but then no matter how many times and which location I repeated it at. I could not get it...
  21. Replies
    6
    Views
    451

    If a previous member did have it, I would be...

    If a previous member did have it, I would be interested to find his posts. See what was going on. Needs so much love. So much. If I ever get it mechanically 100% I'd like to change the colour by way...
  22. Replies
    6
    Views
    451

    2008 Buell Xb12Ss

    Here's a few pics. Not me in pictures. Paint done by previous owner. I just picked it up as my first Buell two months ago. 72 000 Km.
  23. Replies
    35
    Views
    2,647

    Do you have signal lights, and non-warped front...

    Do you have signal lights, and non-warped front and rear disks? For 08 XB12ss.
    Maybe even a working cooling fan. Right side air scoop.

    Let me know.
  24. Replies
    40
    Views
    1,844

    Cleaned off grounds. Didn't really make a...

    Cleaned off grounds. Didn't really make a difference. But it's good for peace of mind. Plus I found two wires that were not crimped at all under the headlight. So I did those up proper.
  25. Replies
    40
    Views
    1,844

    Battery checks out. Just had the stator and...

    Battery checks out. Just had the stator and regulator replaced. The stator was in pieces. Dealer tested the battery.

    I will update once I get the grounds cleaned properly. It was first on my list...
Results 1 to 25 of 41
Page 1 of 2 1 2