Search:

Type: Posts; User: KickerDRB

Page 1 of 2 1 2

Search: Search took 0.08 seconds.

  1. Replies
    43
    Views
    3,462

    Cc83. Jardine tune works great for me, IDS does...

    Cc83. Jardine tune works great for me, IDS does not send the files. I sent my ecm to them to be flashed. I do have a buell tooth dongle and ecmdroid. AFV wanders around a bit but always in the...
  2. Replies
    43
    Views
    3,462

    Great pipe, sounds good. I fought the tune and...

    Great pipe, sounds good. I fought the tune and baro sensor for a summer. Took it off and got the IDS jardine tune from Tim. Bike runs great.
  3. I am a fan of the road draft tube. On my Uly,...

    I am a fan of the road draft tube. On my Uly, ran it next to the fuel line then down by the fuel vent line. Stay simple my friend.
    -Dave
  4. Replies
    701
    Views
    117,898

    Time for some details on the heavy roller. That...

    Time for some details on the heavy roller. That ElCo makes my neck start itchin for a mullet.
  5. Replies
    11
    Views
    2,399

    Another cool X-1, Bell not Buell. IMO similar...

    Another cool X-1, Bell not Buell. IMO similar combination of engineering and “hold my beer and watch this.”
    ...
  6. Replies
    701
    Views
    117,898

    I like it, goes great with the fender flares. ...

    I like it, goes great with the fender flares. Makes me think of cheap beer, ‘back in black’ on a set of road thunders and my old jean jacket.
  7. Replies
    38
    Views
    4,836

    I picked up the xb-sg and a baro sensor last...

    I picked up the xb-sg and a baro sensor last spring. Sounds great, imho better than a repacked jardine rt1. Tuning has been an iterative process, he has been very supportive and responsive. He may...
  8. Replies
    0
    Views
    1,062

    Passenger peg drop brackets

    Saw these over on the badweb site. The guy who fabbed them is not active anymore, i have tried a few different ways of contacting him with no success.

    Looking for a fabricator that is willing...
  9. Thread: Injectors

    by KickerDRB
    Replies
    39
    Views
    4,679

    An easy way to deal with the airhorn clamp. Slip...

    An easy way to deal with the airhorn clamp. Slip a pair of small nutdrivers or very small sockets with an extension over the ears and squeeze them together. I could never get the ziptie trick to...
  10. Replies
    21
    Views
    3,565

    There is a guy selling a set of 06 Uly forks on...

    There is a guy selling a set of 06 Uly forks on badweb
  11. Replies
    5
    Views
    751

    14154

    14154
  12. Replies
    5
    Views
    751

    Nose of the bolt was a good 1/4” away from...

    Nose of the bolt was a good 1/4” away from shouldering out. I made sure the insert was tight. I ended up hand filing the isolator bushing down until the bolt torqued up without binding the...
  13. Replies
    5
    Views
    751

    Front isolator bolt installation

    Reinstating the front isolator bolt after rolling the motor. Cleaned it up and applied anti-sieze. Adjusted motor height with a jack until it threaded in smoothly. When i get to the final torque...
  14. I have an original 1/2” rear master that I took...

    I have an original 1/2” rear master that I took off my 06 Uly. I switched to an 11mm Brembo. It is missing the pushrod, but the plastic reservoir elbow is good. You can have it for the cost of...
  15. It was kind of like watching your parents fight. ...

    It was kind of like watching your parents fight. Fun for awhile, then you start wondering about future consequences. Who will get the kids? Is an older sibling going to step up and fill void. ...
  16. Replies
    22
    Views
    1,497

    Awesome trip! Any ideas why the motor let go? Did...

    Awesome trip! Any ideas why the motor let go? Did the fan quit, or 1,000 miles of low octane detonation?
  17. Replies
    8
    Views
    1,497

    I installed one of these...

    I installed one of these <https://www.ebay.com/itm/200609174686> tri-color LED voltmeter. I was not brave enough to crack open the instrument cluster so it is mounted left side just under the seat...
  18. Left hand drill bits are also an option. If you...

    Left hand drill bits are also an option. If you buy a set, keep them in a pouch no where near the rest of the bits or they will sneak in and burn up.
  19. Replies
    16
    Views
    1,457

    me every time i check this forum- I see something...

    me every time i check this forum- I see something I wondered how I have managed to live without for so long.
  20. Replies
    35
    Views
    3,172

    Looking forward to getting my Uly dirty this...

    Looking forward to getting my Uly dirty this summer. I picked it up late last fall. Here is my list of dirt ready to do items, in no particular order:

    Flush turn signals, prior owner broke off...
  21. Skid plates compatible with non oem exhaust

    Buelligans,

    Any ideas on a skid plate that mounts to the existing chin spoiler brackets. I have an aftermarket exhaust an could probably come up with a reasonable rear bracket. DeanAdams design...
  22. Replies
    2
    Views
    768

    Right on. Thanks!!!

    Right on. Thanks!!!
  23. Replies
    2
    Views
    768

    Front Rotor Alignment and hardware

    All,

    The 2006 Uly service manual states: Front Rotor Installation, align reference dot on the front rotor with the valve stem.

    When removing and reinstalling a used rotor where is this dot? ...
  24. Replies
    1
    Views
    799

    I picked up a kit from SPHD.

    I picked up a kit from SPHD.
  25. Replies
    1
    Views
    799

    WTB - heated hand grip kit

    Wanted- factory heated grip kit w/controller

    Thanks,
    Dave
Results 1 to 25 of 27
Page 1 of 2 1 2