Glad you got it sorted out. Hopefully this weekend I'll get around to looking for that pulley cover.
This is my favorite picture of it. It's the one that made the BuellXB calendar a few years...
Type: Posts; User: nicholas900
Glad you got it sorted out. Hopefully this weekend I'll get around to looking for that pulley cover.
This is my favorite picture of it. It's the one that made the BuellXB calendar a few years...
Hey thanks guys. I haven't checked in this section for a while. Thanks for the kind words. I made a little photo slideshow. My skills with this stuff suck. It cropped all the photos but after trying...
Parts list:
ENGINE
Fuel pump
O2 sensor
Cyl head temp sensor
Fuel injectors
Ignition coil
Plug wires
Thanks guys. I just wanted to say that not only was the build fun, but posting it up on hear was just as much. Thanks for being cool about this. I know some people are totally against modifying a...
http://i940.photobucket.com/albums/ad249/hellboy-5150/Mobile%20Uploads/IMG_20141007_180055_252.jpg
...
Thanks EricZ. That means a lot coming from you. I've seen your work through your posts on your turbo bike, it's outstanding.
Well... I don't know about all that lol. But thanks Wally. Glad some of you guys dig it. As for the cost, I haven't added it all yet. I will though and post it. I think I'm into it for around 7g...
Thanks Camo. That bike you linked is awesome! Gonna be checking those guys out and stealing ideas for the next one.
I fired it up for the first time also. Everything works as it should. No oil leaks or issues. That's a good feeling! I made a short VIDEO but again phone is messed up. It keeps rotating when I take a...
Made some more progress. I finished up all the wiring finally. Getting close.
http://i940.photobucket.com/albums/ad249/hellboy-5150/Mobile%20Uploads/IMG_20141005_175744_124.jpg
...
To answer a few questions,
-The header is polished.
-Will the seat have a cafe "bubble back". The seat is actually done. There are pictures of the bike "mocked" up on page 5 (I think).
- The...
My shock finally arrived. It came with a cool manual and some goodies.
http://i940.photobucket.com/albums/ad249/hellboy-5150/IMG_20140918_183614_157.jpg
As I mentioned I asked them to powder...
^ThanksI did a little DIY on the directionals here. I included a link where I bought them from.
I'll post more when I get to it if there is interest. All these wires will be shrink wrapped. They will exit from the brake side. There are a few mods that need to be done to the hardware supplied...
I made a licence plate mount today. I made it with some of the hubs I made to make my subframe. I like it a lot better than the original one I made. It's just rough steel, I'll have to make another...
Thanks guys.Just got word that my new shock shipped out. Should be here by next weekend. Penske changed their typical reservoir hose mounting to the shock for me. It will use a banjo fitting like the...
Just the muffler. Have to put it back on the jack to swap out shock when my new one gets here.
Little more progress. Really wish I had the shock, but it can be changed with the subframe in place on this bike. So...
I mounted up my rear caliper. It's a brembo caliper using the hidden...
^Thanks fellas
Still waiting on the shock. But needed to get it off the jack to get the oil lines installed. Swing arm and lines done. This is as far as I can go until the shock shows up.
...
Also mounted up the oil cooler and lines. I cut off the old bracket for the voltage rectifier since it is being relocated.
...
I mounted up the main electronics to my cover plate. I forgot to snap a pic. But on the bottom side of my electronics plate I installed a lining:
...
All the front controls mounted up. Finished up all the front end wiring. Starting to take on a personality. It's a good feeling mounting up everything permanent, the bikes been put together and taken...
^ lol. You got good eyes!
I got the front end mounted up. I slid the tubes into the bottom clamp on my workbench. Then slip on the headlight ears and clipons. The headlight ears are a bitch...
http://i940.photobucket.com/albums/ad249/hellboy-5150/IMG_20140823_173241_225.jpg
Little more progress. I changed up the grounding scheme because I'm using a steel subframe. I am using one of the rear isolator bolts as the main ground and ran my negitive cable directly to it. I...