Search:

Type: Posts; User: Cooter

Page 1 of 20 1 2 3 4

Search: Search took 0.58 seconds.

  1. Sorry to correct you, but the "Highest Man Made...

    Sorry to correct you, but the "Highest Man Made Temp" is actually repeatable in my kitchen. It is the plate under my microwave burrito at approximately 500 Billion Zillion degrees.

    The burrito is...
  2. I believe you are chasing a ghost rabbit down...

    I believe you are chasing a ghost rabbit down it's hole. Back up before you self-diagnosed an "intermittent no spark issue" and please answer this as clearly as you can.

    So:
    1) Does your bike...
  3. Replies
    8
    Views
    113

    FYI, It is perfectly fine to re-use the primary...

    FYI, It is perfectly fine to re-use the primary and inspection hole gaskets several times. There is no pressure behind it so there is no need to replace it after every clutch inspection or service...
  4. Replies
    8
    Views
    113

    I have a new Cometic one if you want it.

    I have a new Cometic one if you want it.
  5. Replies
    462
    Views
    112,295

    "The cheaper the parts, the better buy for the...

    "The cheaper the parts, the better buy for the money"
    EL-P
  6. Thread: Cooling fan

    by Cooter
    Replies
    7
    Views
    206

    Your question is posed like you are questioning...

    Your question is posed like you are questioning the temps being higher than you think they should be. You should know your Buell does not have a radiator and as such will not have the tight temp...
  7. Replies
    5
    Views
    145

    :tongue-new:

    :tongue-new:
  8. Replies
    6
    Views
    265

    Do this from post #2

    Do this from post #2
  9. Replies
    5
    Views
    145

    You can jump the pins in the diagnostic connector...

    You can jump the pins in the diagnostic connector if you don't want to wait. Buellmods.com
  10. Thread: Buell muffler ?

    by Cooter
    Replies
    18
    Views
    1,038

    90* elbow between the header and the mounted can....

    90* elbow between the header and the mounted can.


    It's actually slightly less than that, but theres enough wiggle in the slip joint to make it mount ok.
  11. So have you tested for spark during the issue? ...

    So have you tested for spark during the issue?

    Not starting when cold is a common result of fouled plugs. Buells run a very long, very rich, cold start cycle. Starting it cold and running it for...
  12. Replies
    5
    Views
    112

    Well thats good news:eagerness: As long as the...

    Well thats good news:eagerness:

    As long as the bike is in good running order now, it will be perfectly fine with the "Buell Race Muffler". Congrats, those are getting harder to find:angel:
    It is...
  13. Replies
    462
    Views
    112,295

    Hot damn thats pretty! I bought a cheap old...

    Hot damn thats pretty!

    I bought a cheap old Kalawain 17' jet boat in the late 90's with "some old Ford engine" in the back. Funny thing is it would beat up on some pretty well built boats my...
  14. It depends greatly on the circumstances of the...

    It depends greatly on the circumstances of the loss of ignition, but I've had a rash of corroded right handlebar switches lately. Glad they're still cheap! When it's running wiggle test the red run...
  15. Replies
    5
    Views
    112

    Well you're not gonna like this, but here's the...

    Well you're not gonna like this, but here's the facts.

    Throw it away. It can never be as good as what you can do with even the most basic tuning that you can even do for free on a Buell. Thats not...
  16. Fantastic info from Barrett:applause:

    Fantastic info from Barrett:applause:
  17. Replies
    5
    Views
    112

    What does Twin say about it?

    What does Twin say about it?
  18. Replies
    55
    Views
    9,343

    You want a Drummer.

    You want a Drummer.
  19. Replies
    55
    Views
    9,343

    I firmly believe this is why The Buell Boffins...

    I firmly believe this is why The Buell Boffins TBB(TM) decided on hose clamps to solve the thin metal bolted to a paint shaker problem.
  20. Alternatively you could do what KonaRider posted...

    Alternatively you could do what KonaRider posted just above yours... and see if it's a waste of money and time to replace it before you replace it.

    Here is a copy of the manual for you to read...
  21. Thread: Cooling fan

    by Cooter
    Replies
    7
    Views
    206

    That is the "Speed Based Fan Control" option that...

    That is the "Speed Based Fan Control" option that can be toggled on or off using a program like ECMSpy, TunerPro, Or ECMDroid. I hate it too. It's noisy, wears out the fan prematurely (and pointless...
  22. You can narrow down the source of the noise by...

    You can narrow down the source of the noise by using a long screwdriver with a wooden handle to your ear as a stethoscope.

    Wild West Steampunk-ish chain mechanical noise is usually normal. Rythmic...
  23. I have a Barkers pipe and matching ECM for an...

    I have a Barkers pipe and matching ECM for an 1125CR if you're interested;) Similar sound to a Jardine but MUCH higher quality:eagerness:
    However, I'd HIGHLY recommend getting the noise sorted first...
  24. It's not homeless. It is "The Way";)...

    It's not homeless. It is "The Way";)
    https://live.staticflickr.com/65535/51795328830_99a5ec93ee_c.jpg
  25. Replies
    3
    Views
    134

    Depends where you are in the world, Carmen. ...

    Depends where you are in the world, Carmen.

    Buellparts, SPHDOnline, NCCR, Twin Motorcycles, even e-Bay.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4