Search:

Type: Posts; User: d_adams

Page 1 of 20 1 2 3 4

Search: Search took 0.35 seconds.

  1. Replies
    48
    Views
    990

    Far from a stupid guess, it's just some people...

    Far from a stupid guess, it's just some people have far more knowledge than others. Asking questions and taking stuff apart is how you learn. I learned quite a bit more than I knew previously after a...
  2. Replies
    48
    Views
    990

    Plain and simple answer, theft of IP. No physical...

    Plain and simple answer, theft of IP. No physical way possible for two different tuners to come up with identical maps for completely different exhaust systems.

    I've never looked at the...
  3. Replies
    3
    Views
    68

    I haven't done one in probably 2 years, but I...

    I haven't done one in probably 2 years, but I could possibly be talked into it again.
  4. Replies
    3
    Views
    68

    Have one built. 12129

    Have one built.

    12129
  5. Replies
    48
    Views
    990

    Keep in mind that the stock setup was heavily...

    Keep in mind that the stock setup was heavily restricted by the EPA. European models are even more restricted than the US versions due to the noise and smog/pollution laws over there.
  6. Replies
    17
    Views
    285

    Put one of these on it and see how it's really...

    Put one of these on it and see how it's really running. I'm betting you'll be shocked at how far off it really is. https://www.innovatemotorsports.com/products/dlg1.php
  7. Replies
    48
    Views
    990

    No, they do not.

    No, they do not.
  8. Sticky: July4th2019 Use that for a discount code on...

    July4th2019

    Use that for a discount code on exhaust systems.

    http://deanadamsdesigns.com/
  9. Replies
    48
    Views
    990

    DDFI-3 can log the data via pins 1 and 33 on the...

    DDFI-3 can log the data via pins 1 and 33 on the gray connector. You'll have to add the wires to the harness by taking the connector apart and adding them in by hand. It's a bit of a pain to do, I've...
  10. Replies
    4
    Views
    160

    While it's not exactly a common failure, it does...

    While it's not exactly a common failure, it does happen. Clean it up, purge it with argon and weld it with 309 filler. The small dent will not affect the flow of the exhaust gas.
  11. Thread: Dae

    by d_adams
    Replies
    9
    Views
    446

    This is the factory torque spec. Also, the...

    This is the factory torque spec.

    Also, the spacer included depends on how it's mounted. Some require it, others don't. It's dependant on the header mounting and how it's lined up. Most of the time...
  12. Replies
    23
    Views
    1,207

    The cam position sensor is one of the very few...

    The cam position sensor is one of the very few things that can (do) fail with no error codes showing. It *IS* and 03, so it's the cheaper CPS to just replace it and be done. I've had this happen to...
  13. I believe the injectors can be pulled/serviced...

    I believe the injectors can be pulled/serviced without removing the throttle body. Kind of a pita, but it can be done. They're held in with clips that slide off the side, they're Ford injectors or...
  14. Replies
    82
    Views
    12,942

    Sticky: Going to post a few links of tools or parts here....

    Going to post a few links of tools or parts here. If it's not in stock currently, it's being made and will be available within a week or so at most. I'd like to see some of this stuff move out soon,...
  15. Thread: Lean mixture

    by d_adams
    Replies
    4
    Views
    246

    Change your intake seals (lean condition) and new...

    Change your intake seals (lean condition) and new plugs. Verify correct calibration for the ecm/exhaust combination.
  16. Replies
    82
    Views
    12,942

    Sticky: Just placed an order with my machinist, I should...

    Just placed an order with my machinist, I should have these back in stock within the next couple of weeks. Link is live, so if you want a set, go ahead and order it.

    ...
  17. Buell 1125 & EBR 1190 crank locking tool

    Having another batch of these done. Last ones were powder coated in a neon yellow/green to make it hard to lose them. Not sure what color I'll have them done in this time, probably won't be pink...
  18. Btw, an XB with my exhaust is far more mellow...

    Btw, an XB with my exhaust is far more mellow sounding than an 1125 or 1190 with one on it. Lower compression motor that only revs to 7k rpm, that's where the 1125 and 1190 are just getting into the...
  19. Oh stop-uh. It's not that loud.

    Oh stop-uh. It's not that loud.
  20. Replies
    4
    Views
    200

    Aftermarket Buell XB R model fairing stay

    http://deanadamsdesigns.com/cart.php?target=product&product_id=39

    Doing these for the race guys. They're not intended as a stock replacement, so race use only.

    11338
  21. Sucks that they closed down. LAP bought out the...

    Sucks that they closed down. LAP bought out the stock if I read it correctly a couple of months ago. Would have been on my list for a touring cruiser bike.
  22. I'd be looking at the intake seals for leaks if...

    I'd be looking at the intake seals for leaks if it were my bike. Bike should start fine cold, smooth idle and run like a top when warm. All of my tuning has been done with IDSPD over the last few...
  23. Replies
    17
    Views
    621

    Banned. Again... Help IP Address Search for...

    Banned. Again...


    Help IP Address Search for IP Address: "73.83.117.185"
    73.83.117.185 : c-73-83-117-185.hsd1.wa.comcast.net
    Post IP Addresses
    EBR 73.83.117.185 [Find Latest Posts by User]...
  24. I'm right here. Have a look under the seat at...

    I'm right here.

    Have a look under the seat at the ecm. If it has an IDSPD sticker on it like this one, it's been tuned properly.


    11069


    Once it's tuned correctly, it doesn't matter if...
  25. Replies
    4
    Views
    288

    Aluminum. Clean it (remove the paint/powder coat)...

    Aluminum. Clean it (remove the paint/powder coat) and weld it. Probably 5356 filler would be best, 4043 would work in a pinch.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4