Search:

Type: Posts; User: d_adams

Page 1 of 20 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    10
    Views
    333

    I'm at a loss here. The header with the blown out...

    I'm at a loss here. The header with the blown out O2 sensor *CAN* be repaired. What's the link have to do with either replacing or repairing the header have to do with it?

    Are you just wanting to...
  2. Replies
    10
    Views
    333

    https://st-paul-harley-davidson-buell.myshopify.co...

    https://st-paul-harley-davidson-buell.myshopify.com/products/s0101-7aa-genuine-buell-header-all-2004-2010-xb12r-xb12s-xb12x-models-u7b

    You can have the original welded, just make sure it's cleaned...
  3. Replies
    10
    Views
    333

    Lol. The stock header *IS* stainless steel. ...

    Lol.

    The stock header *IS* stainless steel.

    No comment on the rest of the parts you want to buy from them.
  4. "the primary oil/fluid lubricates your...

    "the primary oil/fluid lubricates your transmission...primary drive components...and assorted ancillary bearings and bushings. it does NOT lubricate the clutch assembly. it only lowers its...
  5. Check for an intake leak. I'd suspect the seals...

    Check for an intake leak. I'd suspect the seals are not in good shape.

    If it turns out that they're actually leaking, replace them. While you're at it, clean the throttle body well and reset the...
  6. Replies
    13
    Views
    485

    Chin fairing. ...

    Chin fairing.
    https://www.facebook.com/groups/126669661276941/permalink/672909916652910/?sale_post_id=672909916652910

    The group referenced.
    https://www.facebook.com/groups/126669661276941/
  7. Replies
    3
    Views
    206

    Send the ecm to IDSPD.com (Tim at IDS) and have...

    Send the ecm to IDSPD.com (Tim at IDS) and have them put it back to it's factory state. Absolutely THE best way to know it was done right.
  8. Thread: 1170

    by d_adams
    Replies
    139
    Views
    6,985

    Dumb question here. Why not spend another $300...

    Dumb question here. Why not spend another $300 and install an Innovate DLG-1 wideband setup on it and KNOW how it's really running?

    https://www.youtube.com/watch?v=JncXcAl8J3M
  9. Replies
    3
    Views
    283

    New Castle has them I think.

    New Castle has them I think.
  10. Yes to the red loctite. Remove the subframe...

    Yes to the red loctite. Remove the subframe spacers, you should have one set of bolts extra, put those back in. Basically, remove the spacer bolts, remove the spacers, drop the tail section back...
  11. Replies
    6
    Views
    737

    It did not. :( Fixtures were made, some work was...

    It did not. :( Fixtures were made, some work was done but the guy doing the machining work failed me quite spectacularly. Still using the same machine shop, just different guys getting my stuff done...
  12. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    The first 11 sold quickly enough that I'll be...

    The first 11 sold quickly enough that I'll be doing 11 more due to demand for a total of 22 skid plates. Yes, it's an investment on my part, but you guys are worth it. If you want one, I WILL have...
  13. Replies
    22
    Views
    10,734

    http://www.surdyke.com/PartsMain.aspx?PartNumber=3...

    http://www.surdyke.com/PartsMain.aspx?PartNumber=33900-99&SubCatID=&CatID=&Name=&CatName=NEUTRAL%20INDICATOR%20SWITCH,%20XL

    OEM part # is 33900-99, it may be superceeded by now.
  14. Sticky: https://www.facebook.com/permalink.php?story_fbid=...

    https://www.facebook.com/permalink.php?story_fbid=3416436145034226&id=245433732134499

    Running a presale, 4th of July, 2020. Code is "7-4-2020" and will get you a 10% discount a couple of things....
  15. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    Ok, these are in process as of earlier this week....

    Ok, these are in process as of earlier this week. I am going to go out on a limb here and say they'll probably be done and ready to ship by just after the 4th of July. Go Merica!
    The machine shop...
  16. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    Last call for this. I have 5 firm commits, I'll...

    Last call for this. I have 5 firm commits, I'll do a couple of extras just to make sure the machine shop has the required amount of work to make it worthwhile. I will not be doing these again for a...
  17. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    From the FB post, I should have done this...

    From the FB post, I should have done this earlier, but with the crap I have going on, I miss things occasionally. Cut off date to order one will be the 15th of this month. I will have at least one or...
  18. Replies
    8
    Views
    504

    Temporary hiatus

    I am taking a break from building for the time being, personal/medical issue. I've had quite a few requests over the last 2 weeks for builds, I cannot do so at this time. Long story heavily edited...
  19. Replies
    8
    Views
    446

    This is probably the best option. I've had...

    This is probably the best option. I've had several over the last 10 years and have one on my Uly right now. Assuming you can find one, snatch it up.
    ...
  20. I can call him, he lives about 20 minutes away...

    I can call him, he lives about 20 minutes away from me. He's on FB. I'd offer other help, but I've stopped building stuff for now and taking orders. Semi-long story behind why, not going into details...
  21. Replies
    11
    Views
    761

    I've used some fairly expensive white Krytox...

    I've used some fairly expensive white Krytox grease with very good results. $3-400 for a little ass tube of it, but it works.
  22. Replies
    28
    Views
    2,271

    Not sure I'd recommend oiling the brake hardware,...

    Not sure I'd recommend oiling the brake hardware, things might go south on you.
  23. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    Pretty much last call on this. 2 have been sold....

    Pretty much last call on this. 2 have been sold. That's not enough to justify doing them at all, so by no later than Monday, the 6th of Jan, 2020 the orders will be cancelled and $ refunded back. If...
  24. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    One week remaining to get in on these. Maybe 2...

    One week remaining to get in on these. Maybe 2 weeks if the machine shop takes off for the Christmas week.
  25. Thread: Skid plates

    by d_adams
    Replies
    86
    Views
    13,269

    Ordering is live if you want one. ...

    Ordering is live if you want one. http://deanadamsdesigns.com/cart.php?target=product&product_id=21
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4