Does anyone have a header pipe for a 2005 xb12r motor in good condition they would to sell?
Type: Posts; User: RHYNOXB9R
Does anyone have a header pipe for a 2005 xb12r motor in good condition they would to sell?
Hey Buellers,just finished the swap of putting in a 05' xb12r motor into my 03' xb9r,also did the primary gear swap of the 9's into the 12,on Saturday had a 3 hour Dyno tune session at JTnS...
Great learning process, if your interested, on the xb9r wiring harness, all electrical demands for the bike are connected, the xb12r and xb9r use 98% of the same parts, the terminal between the 2 ECM...
No, the ECM that I put on is for the 2005 xb12r motor that I also just put in, the ECM is from or came with the xb12r motor that is now in my xb9r frame, just wondering if that middle prong in will...
So I put the ECM from the xb12 on xb9, I noticed that the ECM on the 12 has a plug inbetween the two main plug ins and my 9 didn't, is that something on the 12's only and will this affect anything...
Got it done, very tight tolerances, you must have the chain, from the 9, on the front sprocket and the rear and slide them both on at the same time, not the easiest, but doable, then set proper chain...
Doing the xb9 primary gear swap into the xb12 and my primary chain form my xb9 is to short and the primary chain from the xb12 seems to long the xb9 primary gear and chain are from a 2003...
Once again, thank you Terry over at JT&S PERFORMANCE, here in Sonoma County, he took time out of his busy day( its a race weekend ) to talk me through everything over the phone,Terry, YOU DA MAN...
Good morning ,I'm in the process of swapping a 1203 into my xb9r frame, getting to the point, the cam gearcase cover was cracked on the 12 so I went to take off the cover to put my 9's on, while...
Right on Kona,and Yes,im talking about the rear output shaft pulley that conects the belt to the rear sprocket,thank you on the info;)
Fock,did you do anything to lock the sprocket up,like the belt being on,although you did say you were tearing appart your motor, i just dont want to break anything in the tranny,and thanks for the...
Good info kd4gru,just did my pipes with the black Dei wrap tonight,i have hi temp silicone spray and will coat them well,thanks for saving me from losing it;)
Ok,so I have to remove the rear tranny sprocket,the manual tells of a "holding tool"don't have one,has anyone just taken the sprocket off with an air impact? And anyone know the size of the sprocket...
some of the older members on here will remember back when mountainclimber and I did this swap,we were among some of the first,everyone thought it looked stupid,now it is a desired swap,they look...
Just ordered my right side air scoop kit from the HD dealer,some of the prices in these posts,some dates 2009, have changed,the whole kit cost me $100.58 from the dealer,a lot more than listed in...
Looks like I will call JTnS up here in Sonoma,CA,when they open,I'll post and let you guys know if their compateable;)
I would check out www.revolutionperformance.com they have some great big bore kits,have seen their 90ci kit on a xb12,total rocket,all depends on how much your willing to spend,you get what you pay...
Hey Buellers,I am in the process of putting an xb12r motor into my xb9r bike,I am also doing the primary gear switch on my 9's gear into the 12,since I have the rotor and primary gear from my 9...
Hey Buellers,in the process of doing a swap of a xb12r motor into my xb9r,came across this,has anyone else had this kind of wearing on your exhaust mount,I know it's from the oil lines rubbing...
Interested in your ecm if you still have it;)
Can a ecm from a 2003 xb9r be used for a 2004 xb12r motor or are they different? I am swapping out the 9 motor for a 12. Thanks;)
Sweet oh9,I'm going to see if my local HD dealer can get ahold of these today,this should be interesting,thanks for the info.
Has anyone bought one of America Sportbikes right side air scoops for their XB? Does it match well in size and looks to the stock left side scoop? Was thinking about buying one but thought I'd run it...
Hey Buellers,my buddy is building a FXR,he put a front end on that came from a later 90's X1,possibly a S1,swap meet find,question is,has anyone running this front end ever put on another type of rim...
Question is,would a smoked clutch pack cause the shifter to lock,or freeze up? As mentioned before in my clutch basket post,I was on the freeway,rolling 85mph,bike made funny lunging feeling,and then...