Search:

Type: Posts; User: 34nineteen

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    5
    Views
    62

    Heal up quick SR! We miss you around here! :)

    Heal up quick SR! We miss you around here! :)
  2. Thread: St. Paul

    by 34nineteen
    Replies
    8
    Views
    64

    Do a search on here. I think it is in the DIY...

    Do a search on here. I think it is in the DIY section, where it seems like someone documented removing the headers without a rotate.
  3. Thread: St. Paul

    by 34nineteen
    Replies
    8
    Views
    64

    Ah, I found the notice on their website. My guess...

    Ah, I found the notice on their website. My guess is that they shipped something out of the country and weren't supposed to, and someone talked.

    Attention customers outside the US:

    Before we...
  4. Replies
    12
    Views
    387

    fixed it for you. ...

    fixed it for you.

    http://www.buellxb.com/buell_images/1412_20081112211030_L.jpg
  5. Thread: St. Paul

    by 34nineteen
    Replies
    8
    Views
    64

    They probably wanted to get your VIN to verify...

    They probably wanted to get your VIN to verify the year of the bike to make sure they were sending out the correct gaskets. I used to work the parts counter at a GM dealer a looong time ago, and it...
  6. Replies
    9
    Views
    96

    Didnt LF and someone else find something...

    Didnt LF and someone else find something comparable on ebay? It wasnt the kit for the translucent cover, but it was the bolts.


    Maybe this?
    ...
  7. Its much easier to set rear sag with someone...

    Its much easier to set rear sag with someone helping. To measure the front sag, I put a zip tie around a front slider. Endo will recognize this from the mountain bike world.

    I've found the setup...
  8. Replies
    16
    Views
    119

    Yes ^^^^^^^^ The sleeve is aluminum and...

    Yes ^^^^^^^^

    The sleeve is aluminum and relatively inexpensive. I usually replace them when replacing bearings.
  9. Watch the Dave Moss videos about setting up sag....

    Watch the Dave Moss videos about setting up sag. The idea is the same for all bikes. Yes, have a friend help you.

    FYI...Cooter is not a friend. He will drink all your beer and throw small random...
  10. Replies
    16
    Views
    119

    I’d pull the wheel and thoroughly inspect the...

    I’d pull the wheel and thoroughly inspect the bearings.

    Scooter- glad you are ok!!!!!
  11. I didnít hear a grind. However , it may be a...

    I didnít hear a grind. However , it may be a small buzz from the starter from running out of current, and releasing the starter and trying to re-engage.

    To me it sounds like the starter isnít...
  12. Replies
    16
    Views
    119

    My money is on a roached wheel bearing. Probably...

    My money is on a roached wheel bearing. Probably the same side as the belt.
  13. Replies
    14
    Views
    237

    Have you considered using a FULL BRIDGE...

    Have you considered using a FULL BRIDGE RECTIFIER???


    https://www.youtube.com/watch?v=9dtPEk73X9U
  14. Replies
    11
    Views
    126

    You are not wrong. Look up "Squid" and my picture...

    You are not wrong. Look up "Squid" and my picture is front and center. My chicken strips are as wide as the day is long.

    But I am strong with the heckle.
  15. Replies
    19
    Views
    194

    On my last XB, I searched all over for my hook...

    On my last XB, I searched all over for my hook wrench and wound up doing something makeshift. When I was putting the makeshift stuff away, I found the hook wrench hiding in plain sight!
  16. Replies
    19
    Views
    194

    I like his videos as well. I'm glad he stresses...

    I like his videos as well. I'm glad he stresses setting up sag in a few videos, as most people dont do it correctly... or do it at all.

    He is quick to recommend a spring swap to a heavier rate on...
  17. Replies
    14
    Views
    96

    Dan is the man. He is pretty quick to respond via...

    Dan is the man. He is pretty quick to respond via email.

    I've heard one of those Force pipes on an XB9 a few months ago and its sounded mean. It was fricking loud too. It had a "tuned" sound to...
  18. Replies
    11
    Views
    126

    Cooter, take note: leaning AND a knee down.

    Cooter, take note: leaning AND a knee down.
  19. Replies
    14
    Views
    237

    It could be that wire is shorted (or partially)...

    It could be that wire is shorted (or partially) and the ECM is able to go into protection and turn off the current?

    ^^^^ total guess with no basis.

    It wouldnt hurt to check to be sure.
  20. Replies
    15
    Views
    207

    Thats a clean looking Blast as well. Tell us...

    Thats a clean looking Blast as well. Tell us more about your FI conversion. Is it just half of an XB setup?
  21. Replies
    15
    Views
    207

    I didnt know they did a fuel injected Blast? I...

    I didnt know they did a fuel injected Blast? I guess I need to relinquish my "know it all" status back to Cooter


    What caliper are you using on the forks? I'm surprised it lined up with the...
  22. 4 of the 6 places you have pan head screws came...

    4 of the 6 places you have pan head screws came stock with rivets. The bottom 2 behind the front wheel came with T27 torx screws that screw into the stock muffler.
  23. Replies
    15
    Views
    207

    I've considered getting one for giggles, but...

    I've considered getting one for giggles, but afraid I may have to own it the rest of my life. I could leave it downtown with the keys in the ignition, but it would probably just get impounded as...
  24. Thread: Stator

    by 34nineteen
    Replies
    7
    Views
    178

    ^^^ agreed. I have had St Paul be out of...

    ^^^ agreed.

    I have had St Paul be out of something I ordered... once. Doug emailed me promptly and got me taken care of. I always wonder why people try to shortcut them to save a buck.
  25. I agree with you, on every XB I've owned, they...

    I agree with you, on every XB I've owned, they pretty much fall off once the screws are removed.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4