Search:

Type: Posts; User: ROOK

Page 1 of 6 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    0
    Views
    635

    WTB Firebolt Relay/Fuse blocks

    Looking to buy Firebolt relay and fuse blocks that attach to fairing bracket/housing. Let me know if you have anything.

    Parts numbers were Y1201.02A8, Y1200.02A8 - below is a web pic that has...
  2. Yeah, I’m all over the place. I should have...

    Yeah, I’m all over the place. I should have title this differently, explained where I’m at before asking about one specific part of a larger set of options I’m looking at.


    To start over:
    I’ve...
  3. nope, not the same. I knew I needed an SCG clamp...

    nope, not the same. I knew I needed an SCG clamp for SCG forks. Didn't know the turnstop wouldn't allow the clamp to seat into the frame neck.

    15065
  4. yep, albeit a few grand more than an S/SCG Frame....

    yep, albeit a few grand more than an S/SCG Frame. but yeah. I own an Ss right now, and I can get a frame used for a few hundred bucks.

    The silver clamp is from my Ss - fits the larger Ss/Uly/S...
  5. nice writup, and good lookin bike.

    nice writup, and good lookin bike.
  6. They aren't, I knew this and found an SCG lower...

    They aren't, I knew this and found an SCG lower clamp that works with the SCG forks. What I didn't know is that the lower fork has a different steering stop design - the pain is real:
    15061
  7. Replies
    8
    Views
    6,648

    nice.

    nice.
  8. Franken-buell - differences between S/SCG frame and Ss?

    What engine mount/body issues will I run into swapping over Ss engine/ECU/everything to SCG frame? Do I need S/SCG engine mounting bracket, cylinder head bracket, etc??? What other issues?

    I've...
  9. Firebold Upper Triple fit SCG forks and lower triple tree?

    if I get the SCG lower at 41mm, will my firebolt upper fit? I've read some posts that all specifically talk about the scg forks and lower triple needing stay together at 41mm, but I haven't been able...
  10. Replies
    10
    Views
    1,510

    That’s probably what I’ll end up doing, just...

    That’s probably what I’ll end up doing, just using my Ss/Long rails to cut off the end. It’s pretty solid right now, should be fine through the end of summer.
  11. Replies
    10
    Views
    1,510

    Done. SsLong with a short tail. 12241 12242

    Done. SsLong with a short tail.
    12241

    12242
  12. Replies
    10
    Views
    1,510

    I was trying to avoid that question, but what the...

    I was trying to avoid that question, but what the heck. I bought the tool to get it apart pretty easy, didn't need a jig or anything else other than the vice to hold it. When I disassembled I found...
  13. Replies
    10
    Views
    1,510

    forks done. different route on the tail swap:...

    forks done. different route on the tail swap: need to use brackets to raise seat - the gab between it and the tank/cleaner plastic was pretty bad, had to raise them up about 3/4 inch to get it lined...
  14. Replies
    10
    Views
    1,510

    Bracket arrived, much better: 12028 Fork...

    Bracket arrived, much better:
    12028

    Fork seals arrived. Going to get some oil and pull the fork, ready for tools to come.
  15. Replies
    10
    Views
    1,510

    The guys at St Paul Harley Davidson had the...

    The guys at St Paul Harley Davidson had the smaller Firebolt tray fuse holder, so I was able to pick that up when I ordered new fork seals. I could drop a lot of money on that website, with all the...
  16. Replies
    10
    Views
    1,510

    Fork seals... yeah. :upset::D I need one of...

    Fork seals... yeah. :upset::D

    I need one of these for an S:...
  17. Replies
    10
    Views
    1,510

    Fork leak means tail swap time!

    My front fork was leaking, might as well use these tail swap parts I’ve been accumulating! S tail on Ss. This is just the figment mock-up. I think I may have a shop just move the bottom hole up to...
  18. Replies
    1
    Views
    756

    Alright, maybe that was a bit much. Let's drop...

    Alright, maybe that was a bit much. Let's drop this down a bit. $275, make me an offer.
  19. Replies
    1
    Views
    756

    Race fairing set - Yoyodyne Sebimoto

    Merry Christmas someone. Selling the race fairing setup I never installed. Local pickup only, I just don't have the time/energy to ship (Portland, Oregon).

    PM, Email if interested. $350 OBO....
  20. Replies
    16
    Views
    2,290

    I have an '06 Ss that I bought in 2012. Had a...

    I have an '06 Ss that I bought in 2012. Had a hot summer the next year and the fan was working overtime, then gave out. Got a new fan, it was still on all the time. Got the air scoop and it was an...
  21. Replies
    8
    Views
    1,447

    There was a guy here in Portland that sold me the...

    There was a guy here in Portland that sold me the Firebolt parts from a Buell he used for this kit/frame. They're pretty cool to see in person. I think he said he had to convert to a carb from FI.
  22. Well that sucks. I ride in the summer, do a lot...

    Well that sucks. I ride in the summer, do a lot of winter camping and sports (as much as I can) in the winter. Really just an excuse to drive our off-road rigs in the snow and camp by a fire Away...
  23. Off Topic: Moving to Colorado, Denver Area from West Coast. Any thoughts?

    I've got a few jobs in the Denver area I might take. What can folks in the area tell me about moving a family there? I'm currently living in the NW (Portland, OR) and it seems like it could be...
  24. Replies
    0
    Views
    1,097

    Lightning to Lightning-'bolt Conversion - DONE

    Thoughts:

    - I'm going to have to get those shorter clutch/throttle/brake lines sooner rather than later...
    - relayed fuse box install went ok - hopefully the wires aren't burning on the heads... ...
  25. Replies
    4
    Views
    2,319

    Thanks!

    Thanks!
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4