Search:

Type: Posts; User: bannon325

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    189

    Paid $75 to steven Mckinney on FB. The post is...

    Paid $75 to steven Mckinney on FB. The post is still up. You'll have to see it there. I dont know how to post pictures to here, sorry
  2. Replies
    6
    Views
    189

    Just found one new on fb

    Just found one new on fb
  3. Replies
    6
    Views
    189

    Lol..Sounds like a solid plan. Thanks for the...

    Lol..Sounds like a solid plan. Thanks for the reply. You would think it would be a little easier to buy one. Since my post I've found little info on finding a mid pipe. If no success here then ill...
  4. Replies
    6
    Views
    189

    WTB mid pipe for jardine

    Hello fellow Buellers. I am looking for the curved mid pipe for the Jardine rt1 exhaust for the 08 XB12Scg because the mount bracket is broken on mine. Not sure if it can be welded but would rather...
  5. Replies
    18
    Views
    1,030

    Fuses are all good and working. Vr is supplying...

    Fuses are all good and working. Vr is supplying 11v after it gets hot. It charges accurately for about 10 minutes and then hits the 11v range. I bought a vr off of Skyler Croy who is parting out his...
  6. Replies
    18
    Views
    1,030

    Thanks Cooter that's what I figured.

    Thanks Cooter that's what I figured.
  7. Replies
    18
    Views
    1,030

    Lunatic fringe thank you. It just seemed like a...

    Lunatic fringe thank you. It just seemed like a good way to check. Now it appears that I have to get a new voltage regulator...lol. Can you tell me if its better to go oem or aftermarket?
  8. Replies
    18
    Views
    1,030

    So I installed the stator on the bike and used my...

    So I installed the stator on the bike and used my girlfriends mabelline beige cover makeup on one of the armatures to see if it would run off onto any of the magnets in the rotor. Installed the rotor...
  9. Replies
    18
    Views
    1,030

    Ok so its been a couple days since I jb welded...

    Ok so its been a couple days since I jb welded the magnets inside the Rotor hub. Today I tested the old stator into the Rotor on my work bench (not on the crankshaft) and there is clearance but only...
  10. Replies
    18
    Views
    1,030

    Thanks for the info but I just jb welded about an...

    Thanks for the info but I just jb welded about an hr ago with the type that requires a 24hr set up. I did use a little sand paper to roughen it up for a better stick.
  11. Replies
    18
    Views
    1,030

    Thank you and I will do

    Thank you and I will do
  12. Replies
    18
    Views
    1,030

    I miscounted the number of magnets. There are 6...

    I miscounted the number of magnets. There are 6 magnets for the rotor
  13. Replies
    18
    Views
    1,030

    08 xb12scg Stator magnets

    Hi fellows I hope all is well. This is my 1st post so please be easy on me. My stator started going bad a couple weeks ago so I parked it and did the the stator tests. It was putting out 80v a.c. at...
  14. Replies
    14
    Views
    6,890

    Lol...A little late of a reply but yes it's too...

    Lol...A little late of a reply but yes it's too low. On my sch when I mean the outer side of my feet scrape the shoulder or road. To avoid that I simply tuck my feet in as close to the frame as...
  15. Replies
    38
    Views
    10,369

    Hi i haven't read all this post but would like to...

    Hi i haven't read all this post but would like to know if you have a clutch assembly that would fit an 08 xb12scg? Particularly looking for a clutch hub bearing. Forgive me if you have stated any...
  16. Are these protapers still for sale?

    Are these protapers still for sale?
  17. Are these items still for sale?

    Are these items still for sale?
Results 1 to 17 of 18