Search:

Type: Posts; User: uly luigi

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    7
    Views
    1,365

    sounds like the exhaust actuator is not...

    sounds like the exhaust actuator is not functionning, or the cable to the valve on the muffler is broken, most of the XB's have a similar sound with stock exhausts
  2. Replies
    14
    Views
    2,507

    I have heard they do some racing around here, So....

    I have heard they do some racing around here, So. Alabama, didn't even know about the pulls though, sounds like a lot of fun
  3. Replies
    8
    Views
    1,295

    Especially the grounding bundle at the steering...

    Especially the grounding bundle at the steering neck, double check for broken wires at the ring connectors, it will look good but I am almost certain you have 1 or 2 broken grounds at that bolt, once...
  4. Replies
    12
    Views
    2,314

    Roll the pistons up to the top of the jugs and...

    Roll the pistons up to the top of the jugs and clean the carbon of them use a little solvent after you have them as clean as you can get them, to break any oil residue in the groove above the rings...
  5. Replies
    13
    Views
    3,483

    It has been my experience talking to old school...

    It has been my experience talking to old school bikers that open primaries are quite nice to look at, but suck on a daily driver if there is any chance of humidity, the clutch pack gets wet and...
  6. Replies
    13
    Views
    2,071

    Crap, I used to have a picture of an exhaust on...

    Crap, I used to have a picture of an exhaust on Blast I had never seen before, it was a twin can with skid plate that Bubba Blackwell had on his Blast, that thing sounded sweet
  7. Also, riding before it warms up can cause base...

    Also, riding before it warms up can cause base gasket leaks at the jugs and foul plugs pretty quickly
  8. Replies
    13
    Views
    2,996

    I have an idea, what about a non-contact temp...

    I have an idea, what about a non-contact temp reading at the oil cooler, that would be a little closer to actual engine oil temps, I would think, JMHO
  9. Replies
    12
    Views
    985

    take it to a cleaner experienced with leather, I...

    take it to a cleaner experienced with leather, I bet it is 5 yrs of stank finally showing itself
  10. Replies
    7
    Views
    1,197

    Not saying it;s out of the question, just kinda...

    Not saying it;s out of the question, just kinda suspicious someone would part-out an 8K mile bike from a low side accident
  11. Replies
    3
    Views
    688

    Isn't that one of the adjustment screws, rebound...

    Isn't that one of the adjustment screws, rebound or compression, if it is, it has problably been stripped out and staked back in
    Edit: my reading comprehension skills need work, I see now opposite...
  12. Replies
    10
    Views
    1,125

    American sport bike.com, only place I use for...

    American sport bike.com, only place I use for most things Buell
  13. Replies
    7
    Views
    1,197

    Pretty steep price for used "I was told" Uly...

    Pretty steep price for used "I was told" Uly shock, what is the length measurements, does the Pre-Load cylinder look like it has been sliding, when you turn the pre-load all the way up are there...
  14. Thread: Fact!

    by uly luigi
    Replies
    41
    Views
    2,614

    Fact: 99.9% of "Bikers" have absolutely no Idea...

    Fact: 99.9% of "Bikers" have absolutely no Idea about Buells
  15. Replies
    11
    Views
    1,045

    Small world I built several of the DDG's at...

    Small world I built several of the DDG's at Ingall's Shipyard in Pascagoula Ms., I think 112 was built in Maine wasn't it?
  16. Replies
    13
    Views
    3,654

    I was having a rubbing issue with the seat on my...

    I was having a rubbing issue with the seat on my '08 Uly, I caught it before it was able to break my ECM, I took some sidecutters and removed the hard plastic seatpan that was pressing on the ECM,...
  17. Replies
    7
    Views
    1,128

    I wouldn't, take a razor blade and flick the...

    I wouldn't, take a razor blade and flick the gasket off, they are reusable, metal cored, just be careful and put the edge of the blade under the gaket and twist gently, it should just pop loose
  18. Replies
    6
    Views
    1,439

    2010 model 3 bearing wheel is the only "Fix" I...

    2010 model 3 bearing wheel is the only "Fix" I know of
  19. Replies
    8
    Views
    890

    if it is, that is normal, in my experience...

    if it is, that is normal, in my experience anyway, nothing to worry about
  20. Replies
    5
    Views
    728

    xoptiinside.com, everything you need is linked to...

    xoptiinside.com, everything you need is linked to his site, he is the original guy for tuning Buell ecms
  21. Replies
    19
    Views
    995

    Pinion nut on the right side of the crank,...

    Pinion nut on the right side of the crank, holding the cam drive gear, backed off and siezed to the oil pump housing, not a pretty scene at my house right now, galled about an 1/8" of threads on the...
  22. Replies
    19
    Views
    995

    Yep, 17th annual Motorcycle show Sunday April...

    Yep, 17th annual Motorcycle show Sunday April 7th, supposed to be a beautiful day too, but, my Uly is broke, so I won't be there
  23. Replies
    6
    Views
    1,439

    I would advise you to change wheel bearings when...

    I would advise you to change wheel bearings when changing the drive belt, the added tension tends to cause them to fail rather quickly
  24. Replies
    19
    Views
    995

    There is an antique motorcycle show coming up on...

    There is an antique motorcycle show coming up on Dauphin Island, may be this weekend not sure, but we have a ferry that runs from Ft. Morgan to the Island it is a good road to ride on the east side...
  25. Replies
    19
    Views
    995

    I'm in Mobile, Icecoldcoastie is around here to

    I'm in Mobile, Icecoldcoastie is around here to
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4