Search:

Type: Posts; User: lowkey

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    18
    Views
    1,013

    To turn OFF the 02 sensor using ECMDroid the...

    To turn OFF the 02 sensor using ECMDroid the steps are as follows: ECM Parameters / 02 setup / Minimum RPM (600 by default) > change this above spark cut threshold... like 12000 / Now the 02 sensor...
  2. Yellow line TPS? White line RPM? and Red line...

    Yellow line TPS? White line RPM? and Red line acceleration enrichment? Correct? First screen grab shows enrichment at 10% TPS 191... falls below TPD 80-85 degree threshold. Second and third show no...
  3. Replies
    4
    Views
    304

    Have you tested your dash in real time yet?...

    Have you tested your dash in real time yet? Acting buggy (drops in data stream)? Stock sensor definitions should not need to be converted if using the correct .ADX file but I did have a quick look...
  4. Replies
    4
    Views
    304

    I can modify the ADX for a DDFI3 ECM and send it...

    I can modify the ADX for a DDFI3 ECM and send it to you, PM me your email and ECMID along with what all you expect to do with the software. Or include phone and we can discuss further details I will...
  5. Good, glad my rambling came out understandable....

    Good, glad my rambling came out understandable. Haha

    Timing map request? I don't follow, is this a question?

    "I missed the 27" again I don't follow what you are asking here? Are you referring...
  6. I revisited the table and saw it has a TPD 80*at...

    I revisited the table and saw it has a TPD 80*at 1200RPM and jump to 85*at 2000RPM, here is what it would look like overlaid on the fuel map, any TPD value below this line can have acceleration...
  7. 1.) No you misread your link from the ECMSpy...

    1.) No you misread your link from the ECMSpy chapter, it is calculated and applied EACH one revolution of the engine. From my original time stamp with acceleration enrichment = 13.7, in the log...
  8. Totally agree with this and what you are...

    Totally agree with this and what you are interpreting the screen grab is saying, I also fully understand why it is richer than expected (and at the time of this log is exactly what I wanted to be...
  9. To figure out 02 sensor delay I went from the...

    To figure out 02 sensor delay I went from the time stamp peak TPS value then tapped the right arrow on keyboard to the TPS value drop point spike, counted how many taps for the 02 sensor lean spike...
  10. So the ECM is actually processing the fueling...

    So the ECM is actually processing the fueling table cell that isn't actually there but implied, in this time stamp RPM is 2271 and we have data column 1900RPM and 2350RPM and TPS value of 169 with...
  11. Also something I've not seen done once someone...

    Also something I've not seen done once someone goes WB (I don't think they care to put in the time and effort to compare data) is input and log both NB and WB same cylinder at the same time to...
  12. Why is anyone trying to run richer than 14.7-1AFR...

    Why is anyone trying to run richer than 14.7-1AFR at steady state cruise??? This is the ideal burn ratio. There is already a table in place to compensate fueling on acceleration. The acceleration...
  13. I went through some of the screen grabs I got...

    I went through some of the screen grabs I got back when buellitenboard was still around... here is what Mike Cobb (Xoptimized) had to say on setting up the version of MLV that it looks like you are...
  14. It appears you have it set up right, with stock...

    It appears you have it set up right, with stock NB all you can really get an accurate cell hit on the left fueling side corresponding to the right side cells in AFR bin with target of 14.7 (red...
  15. 11983 Here is what stock timing looks like...

    11983

    Here is what stock timing looks like (all values on the circled area TPS 10-20 through 1350RPM have been set to 8 degrees).

    11984

    This is how to tun OFF or ON the temp based timing...
  16. This sounds odd... explain your process for...

    This sounds odd... explain your process for getting the .msq file. I've seen ECMSpy do something similar with .txt files from the internet. I'd suggest running windows signed in as administrator,...
  17. https://www.buellxb.com/forum/showthread.php?6430-...

    https://www.buellxb.com/forum/showthread.php?6430-ECM-Spy-Download&p=555607&viewfull=1#post555607

    The version that works with DDFI2 (2003-2007 XB's) is still available here^, combined with...
  18. Replies
    281
    Views
    147,434

    I'm guessing you didn't bother to hit the link...

    I'm guessing you didn't bother to hit the link and attempt to download that is clearly posted on the previous page? It works fine BTW...
  19. Host the files on Google drive then link what you...

    Host the files on Google drive then link what you want to share here, this is how I do all my file sharing on this forum.
  20. Yugo you need the .msq file, aka map file...

    Yugo you need the .msq file, aka map file (fuel/timing map only extracted from the EEPROM think 2D grid of TPS/RPM cell values) the only software that I know of that can extract this is ECMSpy ..XPR...
  21. So I quickly looked back on the first page, you...

    So I quickly looked back on the first page, you have an 04 XB12 correct? So you have the 0-RPM and 8000-RPM column that are not being utilized on stock mapping. Whatever your TPS value is at the...
  22. Yugo42, your screen shots don't even show the...

    Yugo42, your screen shots don't even show the .msq file was loaded... pull the file with ECMSpy from the EEPROM that was run when you were logging. Load the rear fuel map into the top right, load the...
  23. Replies
    6
    Views
    518

    Don't black out the plastics, find someone who...

    Don't black out the plastics, find someone who will trade... those look like the translucent tangerine orange? Looks like a nice bike.
  24. Replies
    16
    Views
    822

    Cooter, the last portion of the quote was simply...

    Cooter, the last portion of the quote was simply a test ANYONE suspecting a fuel pump problem can perform, this test is by no means accurate in any way BUT performed as outlined give a close idea to...
  25. Replies
    2
    Views
    289

    I don't have a ton of experience with the DDFI3...

    I don't have a ton of experience with the DDFI3 ECM but on a DDFI2 XB you can't simply unplug the 02 sensor to have it run in open loop. You need software and actually turn off the 02 sensor or clear...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4