Search:

Type: Posts; User: dodge

Page 1 of 6 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    16
    Views
    500

    This has me on the right track I think. Its...

    This has me on the right track I think. Its something temp related as well. Early am..65f started up and when I did hard R/L turn it would do the sweep thing. Then when starting up at 80f and turning...
  2. What type of connector for the 08 speed sensor?

    3-way....? Don't want to buy a complete wiring harness...just need a connector pigtail. Not sure who manufactured these/style?
  3. Replies
    0
    Views
    80

    ECM pins #1 and #33..Analog AFRs..

    Anyone exactly what these are/do?
  4. Replies
    16
    Views
    500

    Well, I thought I had the issue resolved when I...

    Well, I thought I had the issue resolved when I found that the WB O2 sensor was not fully tightened. Weird...not problems until I filled up with gas. Was worse than ever sweeping several times within...
  5. Replies
    16
    Views
    500

    Yes, its just like turning off the ignition only...

    Yes, its just like turning off the ignition only more often than not, the engine just stutters briefly, then catches back on. Wish it would throw a code lol.

    thanks
  6. Replies
    16
    Views
    500

    08 Buell-does tach sweep while driving...

    And sometimes just dies. No fault codes. Seems to be happening more frequently...any ideas what might be going on? Is this symptomatic of something going bad perhaps?

    thanks!
  7. Replies
    7
    Views
    508

    Just a quick update-got the speedo working....

    Just a quick update-got the speedo working. Apparently it was a wiring issue at the ecu connector. I had previously had a faulty connection in the connector itself so I pulled all the wires out of...
  8. Replies
    7
    Views
    508

    You're the bomb me. Once the rain stops, I'll go...

    You're the bomb me. Once the rain stops, I'll go check things out.
  9. Replies
    7
    Views
    508

    Code 43....my rigged wiring may be at fault me...

    Code 43....my rigged wiring may be at fault me thinks. There were 2 R/w stripe wires I removed from the ecu connection plug...might have gotten these crossed up. Is there a fuse for the speedo? It...
  10. Replies
    7
    Views
    508

    I think it was 34...speed sensor short?

    I think it was 34...speed sensor short?
  11. Replies
    7
    Views
    508

    Speedometer woes...

    Died. CEL comes on after 3-5' of driving. Replaced the speed sensor today. Still dead. It was a HD sensor that was not a direct replacement...came with the wiring harness and connector which I had to...
  12. Replies
    4
    Views
    1,267

    Trying to tackle this once again.. Got the 08...

    Trying to tackle this once again.. Got the 08 working fine with the baro sensor using ecmspy mono. Trying to do same with the 07, but there are greyed out areas in the 07 settings via mono. The...
  13. Anyone familiar with the HD ver of Megalogviewer?

    Had used the older version years ago, but this senior seems to have forgotten some of the initial settings etc. Using ECMDroid to log MSL files and burn the new tables etc in. Using TunerProRT as...
  14. Replies
    4
    Views
    1,267

    Yeah, was able to set it up using the latest ver...

    Yeah, was able to set it up using the latest ver of ESpy on my 08 and verified it is working by applying either pressure or vacuum to the sensor. But, cant seem to get it up and working on the 07....
  15. Replies
    4
    Views
    1,267

    baro sensor enabled eeprom?

    Anybody have a baro sensor enabled eeprom for the BUEID (2007 XB12S) firmware?
  16. Thread: Tires

    by dodge
    Replies
    9
    Views
    904

    Shinkos

    Shinkos
  17. Replies
    6
    Views
    1,455

    Hey tok-I used the latest version of MLV to remap...

    Hey tok-I used the latest version of MLV to remap tables on both my 07 XB12 and stock 08 XB9SX. Used NTK's latest AFRM wideband sensor and controller. Used ECMDroid to log the data using a 7"tablet...
  18. Replies
    2
    Views
    657

    File format issue or perhaps ecm firmware...

    File format issue or perhaps ecm firmware mis-match?
  19. ERROR: Failed to fetch ecm type: Cable Problem (RX/TX Shorted?)

    Getting this msg when trying to connect using ESpy with either cable or BT module. Bike starts up fine and runs...but cant "talk" with it. What happened??

    update: So I got out this evening and...
  20. Replies
    3
    Views
    879

    Back in the saddle!! yea..

    Back in the saddle!!

    yea..
  21. Replies
    3
    Views
    879

    Hey gunter-thanks for responding! Reinstalled...

    Hey gunter-thanks for responding! Reinstalled everything once again only this time went ahead and filled out the activation form and sent it in. Only did not make a donation a second time. Not sure...
  22. Replies
    3
    Views
    879

    Post reinstall of ECMSpy Mono issue..

    Had to do a Win 10 reset on the Dell laptop. Had a new activation password made and have reinstalled all the needed apps-MONO app, EcmSpy Mono program and the BUE2D database file. Generated a new...
  23. Replies
    3
    Views
    582

    https://www.youtube.com/edit?o=U&video_id=zK7ZNstT...

    https://www.youtube.com/edit?o=U&video_id=zK7ZNstTnys
  24. Just recently completed a re-map of a stock 08...

    Just recently completed a re-map of a stock 08 XB9SX. Used TunerPro RT to enable/disable options and to modify rpm and tps load axis tables. Used EcmDroid to log data and Megalogviewer HD to create...
  25. Replies
    18
    Views
    2,266

    Thanks-well on the way to doing both. MLV is...

    Thanks-well on the way to doing both. MLV is doing exactly what it's supposed to do. Just needed to tweak the curve a tad.
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4