Search:

I'm at NNSY. Trying to sell my Buell though lol

I need the straps and mounts to do it correctly. I don't need the valve. I'm starting work again so I'll probably grab one off ebay before too long.

p.s. - Just snapped the drive belt last...

Still running the dirt bike muffler because funds are tight. It's just making it run a little hot.

Long story short: bought a bunch of parts, went through a lot of troubleshooting, bike is on the road now!

It will never be the cleanest Buell around but at least I'm back on 2!
...

UPDATE: Ran it around for a while with Mobile 1 V-Twin and it would still overheat and throw the engine light anywhere other than the highway.

I dropped the motor because I wanted to put my eyes...

I check my local CL everyday hoping someone will list one for like $50!!

Take a long screw driver and put the tip on different parts of the motor and put the handle to your ear. It will amplify the sound and help you pin point the knock. Make sure you take a listen to...

I would not buy a Blast with that many miles. I think that you can find them so cheap that you can afford to be a little picky on condition. A clean fair mileage one in my area of VA is about $2000.

I wanted to give this thread a bump and see if anyone new sees it.

I've got my 1250 build on the road and I haven't been able to get ahold of Xopti.

I know some of the guys on Dyna's and Sportsters start snapping belts after big bore kits and they can run a little bit wider tire once they do chain conversion.

I've got a 2 wires cut from the main harness, 2 going to the fuse box, and 2 going to the relay box. All the same color. I've looked through the manual and believe they're for the clutch safety...

The manual labels them as Ignition, Key Switch, and Start. They supply several things, I know the ignition relay links to injectors, coil, ECM, speed sensor, and fuel pump.

My bike has an...

Mine hangs like that too. I put a little lube on it where it attached to the intake and it rotates a lot better now.

All 3 of the relays on my 04 XB12R are so hot that you can't touch them for more than 2 seconds. This is only after running the bike a few minutes. I'm probably gonna buy some new ones but it's...

http://i151.photobucket.com/albums/s157/adjwoolley/20140705_160314.jpg

Had to use different cylinder gaskets so I have these left from the standard gasket kit. This is for kit 0934-0817 or ...

Keep working it. Try a screw driver without eating up the pump. Try a rubber mallet to try and break it free. Once you get it out I strongly recommend replacing the 2 large O rings that seal the...

Without seeing a picture, assuming it's clean and it's got everything that's listed I would say the asking price is fair so whatever offer you get him to accept would be a good deal. Some carbon...

Straight from CV Performance?

Anyone in the 757 area good with tuning? Or know of a place in the area with a Buell expert?

Not my bike or anyone I know but if you are in the market for one it looks like this thing is practically brand new!

http://richmond.craigslist.org/mcy/4490752110.html

07 XB12R in Richmond VA

Please message me if you have an oil pump for sale and how much you would like to sell it for. Thanks.

Did it take between 2.5 - 3 quarts of oil when you filled her up?

Hammer Performance = For break-in purposes, any low cost grade of 20W-50 oil will be fine. We actually use the Wal-Mart branded stuff that comes in gallon containers. After break-in (see below),...

Temp sensor is brand new and reading good.

I didn't realize how hot these Buells ran. Only had time to put about 10 miles on it yesterday. Hopefully I can do more tonight. The reason I never...

The battery is a few months old and fully charged.

I can try taking it for a ride and see how goes but If I can't start this bike up, smoke a cigarette, and get geared up without the bike...