Search:

I'll keep the old ones for spares. I received the new bolts for the rear sprocket and they seem to have a gray material on the bolt already. Assume this is some sort of loctite? Do I need to apply...

All though the price seems a bit steep for bolts I located the part number in case anyone else needed it. Seems most places are charging 3 bucks a piece.

AA0609.11CXZB

Anyone happen to know the official part number for the bolts that hold on the rear sprocket on the rear wheel? I am about to remove the rear sprocket and assume these bolts shouldn't be reused....

Am I not allowed to ask questions on a message board because I have been a member for 11 years, 213 posts? My bad....

Am I not allowed to ask questions on a message board..no matter how long I have been a member for?

Thanks fellas

So for quite a while now when refilling the engine oil I was going with the process of filling to just where the oil would barely touch the bottom of the dipstick during a cold check. After a ride of...

Thanks fellas. I'll have to trace it and see where it goes. Will report back

Anyone know where this hose is supposed to be routed? Don't see any obvious area where its supposed to be connected. Since I have had the bike i usually just tuck it on bottom side of the airbox....

Hey everyone,

I need to swap out just the outer oil pump cover on my 2008sb12scg which is part number 1 in the diagram. Is there any bad things that would happen with just replacing that part? I...

Hey Everyone,

I am going to have my primary case powdercoated with a textured flat black and had a few questions on the prep steps I should give the painter. Where the screws go in to attach the...

Hello everyone,

I need to replace my rear wheel on my 2008 xb12scg and was curious if a rear wheel from a 2006 BUELL ULYSSES XB12X would work. Are the wheels exactly the same looks wise and...

Hey Guys,

I seemed to have lost the retaining clips for my bank angle sensor. Anyone know the part numbers for those or am I just better off using a few zip ties? Thanks.

14469

Dang....didn't realize it would be that involved. Velcro it is.

Hey guys,

Busted off the clip on the part of the fuse box that is attached to motorcycle itself. I am assuming to fix my blunder I will need to rip the base out and replace? How much of a pain...

Hey everyone. Have a slow leak in clutch cable on my 2007xb12scg and was wondering if there is any quick fix for this or if I should just replace the whole assembly. The leak is actually coming from...

If I were to completely remove the bleeder valve from the caliper would brake fluid start spilling out? Stupid question...i know, but just curious. I am thinking about installing some speed bleeder...

I went with the BDL Falcon SPC Rear Drive Belt------PART # BDL-SPC-128-118 and it fit nicely. As you can see from my post in this thread...everyone inspect your belts occasionally :)

In terms of visual inspection I would look for similar wear and tear. These pictures were from the belt I just took off my bike.

14313

14314

Thanks guys! The belt has some damage to it. Has a crack starting to form in the middle of the top side of the belt. Looks like something hit it...maybe a rock.

Hello everyone,

Was curious if anyone could recommend a belt I could purchase to replace my current stock belt on my 2007 XB12Scg. Starting to show some wear and tear. Thanks.

Ok..think I'm losing my mind a bit here. Purchased this replacement battery for my 2007 XB12SCG and it seems like its a bit too tall. Seat is kinda making a bit of contact. Can someone tell me if I...

No need to be rude lunaticfringe. I even brought them the relay to look at the pins and amps and they still couldn't help me. Also has them look at stock of AC relays as well. I read your post fully...

I actually found this using my interwebs skills. If anyone needs to know this I believe is the replacement part number as of the present...
...

Any other ideas besides the Duralast Part#19389? I did even ask them at autozone if the Duralast Part#19389 was superseded by a newer part number...to which they had no clue