Search:

Type: Posts; User: Fock347

Page 1 of 20 1 2 3 4

Search: Search took 0.22 seconds.

  1. Replies
    12
    Views
    1,550

    Ok I figured out why I was stuck in gear and...

    Ok I figured out why I was stuck in gear and could not shift, one of the little springs on the shifter paw was missing , I knew it was a problem with the shifter paw.

    And I also cycled thru the...
  2. Replies
    5
    Views
    1,149

    try turning off the o2 sensor and learn mode and...

    try turning off the o2 sensor and learn mode and see what happens
  3. Replies
    5
    Views
    1,149

    kind of sounds like you either have a fuel leak...

    kind of sounds like you either have a fuel leak at the injector , or a bad injector . i would start there , and check the color of your plugs too .
  4. Replies
    11
    Views
    1,372

    i agree with internet annoyance 100%, never use...

    i agree with internet annoyance 100%, never use easy out on aluminum heads,

    lmao my local harley made that mistake on my friends buell and tried to get him to buy a new head.
    heres the story...
  5. Replies
    55
    Views
    8,272

    oh my bad, but the crank sensor could be your...

    oh my bad, but the crank sensor could be your problem , ive had issues like that with cars same symptoms , im pretty sure you can use a volt meter to check the crank sensor while your cranking over...
  6. Replies
    55
    Views
    8,272

    stupid question but did you install the cam...

    stupid question but did you install the cam timing sensor and did you plug it in . Or its burnt out
  7. Thread: rocker boxes

    by Fock347
    Replies
    1
    Views
    992

    im pretty sure you can order gaskets from H-D...

    im pretty sure you can order gaskets from H-D or cometic. as far as removal id recommend putting the motor at tdc. and loosening the rocker box bolts in 1/4 turns increments in a criss cross...
  8. Replies
    12
    Views
    1,550

    ya its in the middle of the clutch pack under the...

    ya its in the middle of the clutch pack under the snap ring that holds the clutch relase shaft thing that screws into the clutch ramp, its a left hand threaded nut
  9. Replies
    42
    Views
    2,041

    I'm by 294s and 95th st, Burbank pretty much ,

    I'm by 294s and 95th st, Burbank pretty much ,
  10. Replies
    12
    Views
    1,550

    ok i feel like such a dumbass i forgot to put ...

    ok i feel like such a dumbass i forgot to put the nut behind the clutch on . so now it doesnt make any noise, but im stuck in 3rd gear now .
  11. Replies
    12
    Views
    1,550

    i had dragos bike works in rockford Illinois ...

    i had dragos bike works in rockford Illinois balance the crank and i think he just put new bushings in the rods bearings that was about 450$ ,
    i had a local machine shop press the bearings and...
  12. Replies
    12
    Views
    1,550

    http://www.buellxb.com/buell_images/1582_201307280...

    http://www.buellxb.com/buell_images/1582_20130728013427_L.jpg
  13. Replies
    12
    Views
    1,550

    Had to rip it apart and bend the detent back it...

    Had to rip it apart and bend the detent back it was pretty bent lol ill post a pic . But no biggie only took 12 hours start to finish , plus got to take a peek inside the motor n see how everything...
  14. Replies
    12
    Views
    1,550

    Ya it was the detent lol, I feel like such a...

    Ya it was the detent lol, I feel like such a squid lmao, guess I didn't push it back far enough when I was puttin the cases back together, yoi live n learn , sometimes the hard way lol
  15. Replies
    12
    Views
    1,550

    so i just got done rebuilding my motor, and...

    so i just got done rebuilding my motor, and before i put the crank in ect, i tested the tranny to make sure it shifted

    ect and it did, now that i have the motor in the bike it doesent want to...
  16. Replies
    10
    Views
    1,197

    most likely 1/4 20

    most likely 1/4 20
  17. Replies
    6
    Views
    1,219

    i ended up using one of those chain oil filter...

    i ended up using one of those chain oil filter wrenches to hold it lol, since i did it with the motor out
  18. Replies
    6
    Views
    1,219

    its reverse thread nut , n its locktited on, a...

    its reverse thread nut , n its locktited on, a impact should do it, i used a breaker bar when i was taking my motor apart, heating it up helps alot too. i cant remember the size tho .
  19. Replies
    12
    Views
    2,130

    i just learned some new info about running...

    i just learned some new info about running synthetic oil in the primary.
    i was at dragos the other day droppin my crank off , and he told me they dyno tested synthetic and non synthetic in the...
  20. Replies
    2
    Views
    1,206

    i have one if your interested primary gear with...

    i have one if your interested primary gear with chain and stator magnet about 20k miles on it. opps i just noticed its for a 08, mines off a 05 it wont work
  21. Replies
    828
    Views
    105,872

    i just got this jalopy a few months ago ,colt...

    i just got this jalopy a few months ago ,colt le6920 magpul edition its not bad.

    http://www.buellxb.com/buell_images/1582_20130528122810_L.jpg
  22. Replies
    12
    Views
    2,130

    amsoil all the way, i run it in everything, got...

    amsoil all the way, i run it in everything, got about 80k on my buell b4 it started knockin. i just posed a few pics of my motor/ the shift forks are still good as well just minor wear, btw i never...
  23. Replies
    1
    Views
    636

    never mind i found them its part number 0903-0584...

    never mind i found them its part number 0903-0584 and its from drag specialties.
  24. Replies
    1
    Views
    636

    does anyone know where i can get 0.10 overbore...

    does anyone know where i can get 0.10 overbore pistons for the 05 xb 12?
  25. Replies
    0
    Views
    588

    so my motor started knockin, so i figured i tare...

    so my motor started knockin, so i figured i tare it apart and see whats wrong , looks like the #2 piston has bad scoring on the back side, and i figured i can check my tranny gears while im at it,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4