Search:

Type: Posts; User: 34nineteen

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    14
    Views
    126

    Thats a clean looking Blast as well. Tell us...

    Thats a clean looking Blast as well. Tell us more about your FI conversion. Is it just half of an XB setup?
  2. Replies
    14
    Views
    126

    I didnt know they did a fuel injected Blast? I...

    I didnt know they did a fuel injected Blast? I guess I need to relinquish my "know it all" status back to Cooter


    What caliper are you using on the forks? I'm surprised it lined up with the...
  3. 4 of the 6 places you have pan head screws came...

    4 of the 6 places you have pan head screws came stock with rivets. The bottom 2 behind the front wheel came with T27 torx screws that screw into the stock muffler.
  4. Replies
    14
    Views
    126

    I've considered getting one for giggles, but...

    I've considered getting one for giggles, but afraid I may have to own it the rest of my life. I could leave it downtown with the keys in the ignition, but it would probably just get impounded as...
  5. Thread: Stator

    by 34nineteen
    Replies
    7
    Views
    164

    ^^^ agreed. I have had St Paul be out of...

    ^^^ agreed.

    I have had St Paul be out of something I ordered... once. Doug emailed me promptly and got me taken care of. I always wonder why people try to shortcut them to save a buck.
  6. I agree with you, on every XB I've owned, they...

    I agree with you, on every XB I've owned, they pretty much fall off once the screws are removed.
  7. It is a good voltage reading, but it sounds like...

    It is a good voltage reading, but it sounds like the issue is amperage.

    You may want to clamp a jumper cable from the negative terminal on the battery to a point on the engine to take that...
  8. So did the front two mounting holes behind the...

    So did the front two mounting holes behind the tire, actually have rivets in them?

    I've drilled out those rivets between the side pieces and center piece and replaced them with small screws/bolts,...
  9. Replies
    4
    Views
    57

    I would think you are on the right path with...

    I would think you are on the right path with that, but I would have to check the FSM to be sure.

    And I agree about your idea that the ~6v is causing the amperage to ramp up. Usually that causes...
  10. But did you change your battery with a high...

    But did you change your battery with a high quality model that puts out at least 220CCA? Also, did you check ALL of your connections, including grounds? Electricity needs to make a complete circuit...
  11. Sounds like a weak battery, or you may need to...

    Sounds like a weak battery, or you may need to clean your battery terminals, and ground points.
  12. Replies
    4
    Views
    57

    Check your relays. You may have damaged one of...

    Check your relays. You may have damaged one of them in the process.

    https://www.buellxb.com/forum/showthread.php?56032-09-xb12ss-electrical-issue
  13. Replies
    77
    Views
    3,218

    Admit it, you got chicked! With a fraction of the...

    Admit it, you got chicked! With a fraction of the displacement!!

    You’d better pick up that tri-glide before they stop making them!!!
  14. Replies
    1,469
    Views
    120,521

    Unfortunately I made the bad choice of buying a...

    Unfortunately I made the bad choice of buying a Klein Aura in 2005/2006 instead of a Lemond Versailles or even a Sarthe/Croix de Fer.

    That would have been really cool to see that exhibit at the...
  15. Replies
    1,469
    Views
    120,521

    He wasnt alone... check this out. A 1996 Klein...

    He wasnt alone... check this out. A 1996 Klein Attitude mountain bike. I think this was tequila sunrise. Lots of very forward thinking tech in this bike for its day. They were bought by Trek in...
  16. one bag of 10. the size is listed on the website,...

    one bag of 10. the size is listed on the website, so he can run with that, if he ever gets the rivits drilled out. its going to be a bear to screw these in with the rivits in place.
  17. Replies
    30
    Views
    538

    Ha! I'm calling you next time I do a set without...

    Ha! I'm calling you next time I do a set without a rotate! I found it to be a huge PITA with the James Blue seals (with the lip). I couldnt get the intake to sit squarely over the ports due to the...
  18. Replies
    30
    Views
    538

    Since you are going to rotate the motor, it...

    Since you are going to rotate the motor, it shouldnt be bad installing the James blue seals. However, if the motor is not going to be rotated, the stock Harley seals are probably the better bet. Even...
  19. Replies
    2
    Views
    73

    I like his videos too. He is really doing a great...

    I like his videos too. He is really doing a great job with the content and amount of videos he is putting out there. Even though I dont agree with everything he says, I do enjoy his videos.

    It...
  20. Replies
    23
    Views
    456

    I agree with Cooter. Casual observer, go back to...

    I agree with Cooter. Casual observer, go back to casual observing.
  21. This ^^^^^^^^ Its a 10 year old filter you...

    This ^^^^^^^^


    Its a 10 year old filter you left sitting in a pool of gasoline for 5 years.
  22. Replies
    5
    Views
    90

    Yeah, it looks like the XB is the least of your...

    Yeah, it looks like the XB is the least of your worries. I had my house in Houston flood TWICE. Once during a tropical storm, after Hurricane Ike (which did literally no damage), and when the...
  23. Replies
    5
    Views
    129

    You may want to contact Bottpower and ask them...

    You may want to contact Bottpower and ask them what their suggestion is. I'm sure they have done a conversion like this before.
  24. well the nice part is that you wont have to drill...

    well the nice part is that you wont have to drill out those rivets. if you use a t27 torx driver and twist counterclockwise you should be able to get them loose.

    unless someone else decided to put...
  25. unbolt fasteners. pull forward and drop downwards...

    unbolt fasteners. pull forward and drop downwards while flexing slightly.

    if you want to pull apart, you just need to drill the 2 rivits from either side. the center piece will just stick to the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4