Search:

Type: Posts; User: 45vtwin

Search: Search took 0.41 seconds.

  1. Replies
    12
    Views
    6,110

    Thank you. I did not know about them.

    Thank you. I did not know about them.
  2. Replies
    12
    Views
    6,110

    Mike, thanks for the pic. But I don’t have the...

    Mike, thanks for the pic. But I don’t have the room on a XB12R for universal billet bracket.
    34ninteen, where did you Source those part numbers from. I’ve looked at LP eBay store and didn’t find...
  3. Replies
    12
    Views
    6,110

    Ok, what I need are EBR part numbers: C3602.1B9...

    Ok, what I need are EBR part numbers:
    C3602.1B9 Clamp, Master cylinder W/ mirror mount.
    H0881.1B9 Bracket, Front brake remote reservoir.
  4. Replies
    12
    Views
    6,110

    Sorry for the omission, I am replacing the XB12R...

    Sorry for the omission, I am replacing the XB12R master cylinder with the one from an EBR. The XB’ screws for clamp are offset and the EBR master cylinder are not and didn’t come with the clamp....
  5. Replies
    12
    Views
    6,110

    Need parts or pictures

    I’m upgrading my XB12R with the ZTL2 caliper. I purchased a new master cylinder but it didn’t come with the clamping end cap. Does anyone have a spare they are willing to part with? Or I can make one...
  6. Replies
    1
    Views
    1,501

    Wrist Pin Reamer

    I am doing a little top end work, I have removed and replaced one wrist pin. Used the reamer that came with the kit, But the Pin is tight. Tight means, once the wrist pin is pushed in it dose not...
  7. Replies
    20
    Views
    8,202

    Hello Atank, I used Oxi Clean and Boiling...

    Hello Atank,

    I used Oxi Clean and Boiling water. Be careful with the Oxi Clean and hot water it will bubble and expand very quickly. I dissolved some in warm first then poured in the boiling...
  8. Replies
    4
    Views
    3,109

    Lessons learned 1) Do not try to trouble shoot...

    Lessons learned
    1) Do not try to trouble shoot anything at 1:00am after a hard days work (at least for me).
    2) Make sure you have a great vantage point and glasses to see how things are put...
  9. Replies
    4
    Views
    3,109

    CEL won't come on

    I'm at the point to crank the engine of my new project XB12R. When I turn the key on, the CEL does not light up and it won't crank over. I have gone through the trouble shooting steps in the manual....
  10. Replies
    1
    Views
    689

    Connector for fuel pump

    I have another project, 2004 XB12R. It is basket case that I'm restoring. The connector for the fuel pump on the harness side is missing. Does anyone have a part number and vendor for this or a...
  11. Replies
    2
    Views
    714

    Hello Snrusnak, Do you still have the Firebolt...

    Hello Snrusnak, Do you still have the Firebolt headlights?
  12. Replies
    20
    Views
    8,202

    Hello Noel, Do not hack that pump. One E clip...

    Hello Noel,

    Do not hack that pump. One E clip holds everything together. Take it apart and then use it as cap and clean out the tank while you wait for replacement parts to rebuild it. There is a...
  13. Replies
    20
    Views
    8,202

    Hello Lunatic fringe. That link to the Ford barn...

    Hello Lunatic fringe. That link to the Ford barn was spot on. I believe it is the same black flaky substance. Now the issue is cleaning without volatile chemicals. Thanks for offer on the pump,...
  14. Replies
    20
    Views
    8,202

    Yep, it is bad. This is some of what came out...

    Yep, it is bad. This is some of what came out after soaking. Any ideas on what to use to clean out this tank.
    Tried Oxi Clean from some searches on other forums. Still have some left.
    What ever...
  15. Replies
    20
    Views
    8,202

    XB9S Gas Tank (Frame) cleaning Help

    I have the sickness, just bought another Buell. First one was a 2006 XB12X
    This one is a 2003 XB9S and has been sitting awhile and does not start.
    The fuel pump is dead. I have bought all the...
  16. P.O already took care of that.

    P.O already took care of that.
  17. Thanks everyone for your help. So far so good. ...

    Thanks everyone for your help.
    So far so good.
    Fifty miles and no issues. Replacing the TPS seems to have solved the problem. I used ECMDROID and Ohmmeter but didn’t see anything wrong. Checked...
  18. I was thinking the same. I’ve removed the fuel...

    I was thinking the same. I’ve removed the fuel pump assembly. Check the wire, no chaffing.
    What do you recommend for replacements.
    Have you tried pump kits from the Fuel Pump Factory?
  19. Hello lunaticfringe I have tried two ECM's....

    Hello lunaticfringe
    I have tried two ECM's. Both had gotten warm while trying to sort out why the bike dId not start. I believe the the warming was due to the 5 volt sensor power was grounded by...
  20. 06 Ulysses misses and stuttering, generally running poorly

    Hello
    New to the forum, have gained a lot of information regarding this common issue.
    I recently picked up this 06 XB12X. I purchased knowing it didn't run.
    1) it would turn over just won't...
Results 1 to 20 of 20