Search:

Type: Posts; User: d_adams

Page 1 of 20 1 2 3 4

Search: Search took 0.40 seconds.

  1. Thread: Dae

    by d_adams
    Replies
    9
    Views
    371

    This is the factory torque spec. Also, the...

    This is the factory torque spec.

    Also, the spacer included depends on how it's mounted. Some require it, others don't. It's dependant on the header mounting and how it's lined up. Most of the time...
  2. Replies
    23
    Views
    1,163

    The cam position sensor is one of the very few...

    The cam position sensor is one of the very few things that can (do) fail with no error codes showing. It *IS* and 03, so it's the cheaper CPS to just replace it and be done. I've had this happen to...
  3. I believe the injectors can be pulled/serviced...

    I believe the injectors can be pulled/serviced without removing the throttle body. Kind of a pita, but it can be done. They're held in with clips that slide off the side, they're Ford injectors or...
  4. Replies
    82
    Views
    12,775

    Sticky: Going to post a few links of tools or parts here....

    Going to post a few links of tools or parts here. If it's not in stock currently, it's being made and will be available within a week or so at most. I'd like to see some of this stuff move out soon,...
  5. Thread: Lean mixture

    by d_adams
    Replies
    4
    Views
    233

    Change your intake seals (lean condition) and new...

    Change your intake seals (lean condition) and new plugs. Verify correct calibration for the ecm/exhaust combination.
  6. Replies
    82
    Views
    12,775

    Sticky: Just placed an order with my machinist, I should...

    Just placed an order with my machinist, I should have these back in stock within the next couple of weeks. Link is live, so if you want a set, go ahead and order it.

    ...
  7. Buell 1125 & EBR 1190 crank locking tool

    Having another batch of these done. Last ones were powder coated in a neon yellow/green to make it hard to lose them. Not sure what color I'll have them done in this time, probably won't be pink...
  8. Btw, an XB with my exhaust is far more mellow...

    Btw, an XB with my exhaust is far more mellow sounding than an 1125 or 1190 with one on it. Lower compression motor that only revs to 7k rpm, that's where the 1125 and 1190 are just getting into the...
  9. Oh stop-uh. It's not that loud.

    Oh stop-uh. It's not that loud.
  10. Replies
    4
    Views
    179

    Aftermarket Buell XB R model fairing stay

    http://deanadamsdesigns.com/cart.php?target=product&product_id=39

    Doing these for the race guys. They're not intended as a stock replacement, so race use only.

    11338
  11. Sucks that they closed down. LAP bought out the...

    Sucks that they closed down. LAP bought out the stock if I read it correctly a couple of months ago. Would have been on my list for a touring cruiser bike.
  12. I'd be looking at the intake seals for leaks if...

    I'd be looking at the intake seals for leaks if it were my bike. Bike should start fine cold, smooth idle and run like a top when warm. All of my tuning has been done with IDSPD over the last few...
  13. Replies
    17
    Views
    593

    Banned. Again... Help IP Address Search for...

    Banned. Again...


    Help IP Address Search for IP Address: "73.83.117.185"
    73.83.117.185 : c-73-83-117-185.hsd1.wa.comcast.net
    Post IP Addresses
    EBR 73.83.117.185 [Find Latest Posts by User]...
  14. I'm right here. Have a look under the seat at...

    I'm right here.

    Have a look under the seat at the ecm. If it has an IDSPD sticker on it like this one, it's been tuned properly.


    11069


    Once it's tuned correctly, it doesn't matter if...
  15. Replies
    4
    Views
    275

    Aluminum. Clean it (remove the paint/powder coat)...

    Aluminum. Clean it (remove the paint/powder coat) and weld it. Probably 5356 filler would be best, 4043 would work in a pinch.
  16. Replies
    4
    Views
    275

    Pic of what's broken would be beneficial.

    Pic of what's broken would be beneficial.
  17. Replies
    32
    Views
    9,358

    Sticky: Get the proper tool to do the job. Adding stress...

    Get the proper tool to do the job. Adding stress to the transmission is just silly. Snap off one tooth and you're looking at a considerably larger amount of work and cost for repairs.
  18. Replies
    7
    Views
    446

    Easily 15+ hp and 10 ft/lbs of torque is a huge...

    Easily 15+ hp and 10 ft/lbs of torque is a huge difference comparing it to stock and if you compare just the aftermarket, it's still a 8-10 hp difference and 5-6 ft/lbs torque. At 7500 rpm, it's a 15...
  19. Replies
    7
    Views
    446

    More than 15 years ago? Was done by ASB back in...

    More than 15 years ago? Was done by ASB back in the day. Website is long since closed but the files from it are still floating around. They did the same type of testing for the 1125 as well in 2010....
  20. Replies
    37
    Views
    1,966

    There are cutouts on the back side of the...

    There are cutouts on the back side of the caliper, they'll line up with the spokes. Tape the spokes off with masking tape to prevent scratching. Use a flat blade screwdriver to push/pry the pads back...
  21. It's a good tool to have on hand just so you...

    It's a good tool to have on hand just so you don't mess up the cam timing on reassembly, but not needed if you have been into these motors and know what you're doing without it. There are 2 other...
  22. Replies
    18
    Views
    960

    27k on the clock, it's probably due for a little...

    27k on the clock, it's probably due for a little bit of maintenance. 1st thing I'd look at and probably just change out on GP is the intake seals.
  23. Thread: Skid plates

    by d_adams
    Replies
    69
    Views
    8,188

    5 remaining....

    5 remaining. http://deanadamsdesigns.com/cart.php?target=product&product_id=21
  24. Replies
    2
    Views
    216

    10816

    10816
  25. Thread: Adding o2 bung

    by d_adams
    Replies
    32
    Views
    1,256

    Sorry man, I'll withdraw my comments.

    Sorry man, I'll withdraw my comments.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4