Search:

Type: Posts; User: Mash199

Search: Search took 0.00 seconds.

  1. Replies
    26
    Views
    2,096

    I ordered the part from eBay, handle not...

    I ordered the part from eBay, handle not included. I had planned to use the crank sprocket nut and a ratchet to push it on. Once I get it, I plan to model it in SolidWorks and post it somewhere so...
  2. Replies
    26
    Views
    2,096

    So I went on a hunt through the service manual...

    So I went on a hunt through the service manual and found this page. I do believe this is the correct installer tool for Xb crank seals.
    Part No. B-45676

    13538
  3. Replies
    26
    Views
    2,096

    I watched the video, though I rewatched it after...

    I watched the video, though I rewatched it after your suggestion just to make sure, and I started to think you might be right about fitting between the lips. I came out to check how it fit on the new...
  4. Replies
    26
    Views
    2,096

    Pictured is the 3d printed part HD-#45206 along...

    Pictured is the 3d printed part HD-#45206 along side the old seal. As you can see, the diameter of the tool is not sufficient to reach the outer lip of the seal, leading me to assume this is just the...
  5. Replies
    26
    Views
    2,096

    My friend fell through but my brother knows a few...

    My friend fell through but my brother knows a few people, he's got someone printing it for 10 bucks
  6. Replies
    26
    Views
    2,096

    Hey all, so I did a bit of digging and I couldn't...

    Hey all, so I did a bit of digging and I couldn't find a place to actually buy the seal installer tool. What I did find, however, is a 3d model to print or CNC the exact part needed. Here's the link....
  7. Replies
    26
    Views
    2,096

    This is the advice I was looking for. I...

    This is the advice I was looking for. I appreciate how thorough your response is, even if I am a little frustrated that I'll have to source ANOTHER specialty tool. I should mention that the rigid...
  8. Replies
    26
    Views
    2,096

    I appreciate the advice, and I will definitely...

    I appreciate the advice, and I will definitely look into it. When I say I've been using "Harley" brand fluids, I was simplifying things a bit. Lately I've been buyi g drag specialty fluid from a...
  9. Replies
    26
    Views
    2,096

    I certainly don't. Buells run a wet clutch which...

    I certainly don't. Buells run a wet clutch which will behave differently depending on the fluid that's in it. One year I put some off brand clutch case fluid in my primary and my clutch started to...
  10. Replies
    26
    Views
    2,096

    Not the outside. I thought that would open up...

    Not the outside. I thought that would open up more possibility of leakage later on.
  11. Replies
    26
    Views
    2,096

    Trans fluid as in Harley chain case fluid. Its...

    Trans fluid as in Harley chain case fluid. Its shared with the trans.
  12. Replies
    26
    Views
    2,096

    05 XB9SX Crank Seal Assistance

    I performed a full teardown over the winter in order to repair the trans, the shift drum was slightly damaged but it's all straightened out now. When I originally put the case halves back together,...
  13. Replies
    20
    Views
    12,722

    Can you be more specific about what you did to...

    Can you be more specific about what you did to readjust your shift pawl? I've been having this exact problem lately, 05 XB9SX. I tore into the primary and took a look, everything seemed to be in...
  14. Replies
    69
    Views
    21,629

    Marcel, I would very much like to know where you...

    Marcel, I would very much like to know where you got these twin LED's. They look like Harley Daymakers, but I haven't had any success finding a set that fits inside the housing. I am also very much...
Results 1 to 14 of 16