Search:

Type: Posts; User: lowkey

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. You are correct but you want the O2 signal...

    You are correct but you want the O2 signal deactivated from the ECM (making adjustments off the signal) for logging. The voltage for NB is 0-1 and WB is 0-5 also the voltage is reversed for AFR...
  2. 11336 Here is race vs stock EEPROM's...

    11336

    Here is race vs stock EEPROM's enrichment tables(BUEGB vs BUEIB), I have no way to verify if the data was changed or not as I got them from the internet and not an ECM. The ECMID checks out...
  3. Hook up the sensor and pull it out of the header,...

    Hook up the sensor and pull it out of the header, what AFR and voltage reading do you get? If it reads max lean AFR and 0 volts you will need to track down the data if it reads max AFR but has a...
  4. Be wary of the info on that site, I read through...

    Be wary of the info on that site, I read through the link to the end you posted and there is bad info IMO... Read/save and reread/referance the ECMSpy MONO tuning guide, it will answer everything you...
  5. The error mask isn't turning off the O2 sensor...

    The error mask isn't turning off the O2 sensor just stops the flag from triggering the ECM. You can do the same procedure to turn off the O2 sensor in ECMDroid as the screen grab I posted above for...
  6. Found it! I took my EEPROM and saved it with...

    Found it! I took my EEPROM and saved it with ECMSpy checked and unchecked for O2 off then loaded both into TunerproRT and had it check for differences in the EEPROM. Just need to put minimum RPM to...
  7. I use ECMDroid to datalog. I will have to find...

    I use ECMDroid to datalog. I will have to find how I was turning the O2 sensor on and off for the ECM to adjust off of. I just looked in ECMDroid but the option is grayed out. In old version of...
  8. Also I do not know if 255 is actually 100% duty...

    Also I do not know if 255 is actually 100% duty cycle on the injector, I would hope BUELL left a safety margin in them of 20% as it is well known not to tune past 80% duty cycle on an injector. All I...
  9. No, you need to disable closed loop to lock the...

    No, you need to disable closed loop to lock the ECM. Setting AFV to 100% simply takes out the AFV multiplier on all fueling cells when running the whole fuel map cells in open loop (doesn't apply to...
  10. :applause: Well played sir! How you been? Got...

    :applause: Well played sir! How you been? Got your bike running properly I hope?
  11. Here's a couple more screen grabs, this time how...

    Here's a couple more screen grabs, this time how to setup a wideband properly in Megalog.

    11307

    Here is the calculated linear line I used the graph software linked earlier to make, this allows...
  12. Yep those look exactly right for the race .bin,...

    Yep those look exactly right for the race .bin, which was my starting point for tuning.
    11306

    If you want to edit your rows and columns, use these axis tables under the tables tab. These are mine...
  13. Also not directed at anyone but just want to...

    Also not directed at anyone but just want to spread how AFV actually works. When you have closed loop enabled each fuel map has two sections closed and open loop. O2 data is constantly used in closed...
  14. AFV was locked at 100% as well as closed loop...

    AFV was locked at 100% as well as closed loop disabled for all times datalogging with the WB mentioned above. The 105% is where AFV was at before disabling closed loop for initial datalog, just want...
  15. Crosshack84 sure, I'll have to do it in a day or...

    Crosshack84 sure, I'll have to do it in a day or two when I can boot into windows and pull the data. It takes a lot of rides to dial in the maps because of flushing out the useless data from the...
  16. Nothing as cool as that sounds. I just cut off...

    Nothing as cool as that sounds. I just cut off the connector that a stock NB has and wired it to the WB harness signal wire so I can hot swap the signal wire feeding the ECM that sits close to the...
  17. If you have a 12 you can use the 0 and 8000...

    If you have a 12 you can use the 0 and 8000 column somewhere useful in the working RPM range, you could rescale the TPS rows and RPM columns as well.
  18. If you are going to go through the effort of wide...

    If you are going to go through the effort of wide band tuning, weld in 2 more bungs, one in the 2010 XB front header location and one that clears the RSS. Take a single wire narrow band sensor and...
  19. I put on the Ulysses brackets on my STT(same as...

    I put on the Ulysses brackets on my STT(same as the SS), it makes riding long distance much better on the legs, if you do the brackets from the Ulysses, you will also need the extended shift linkage...
  20. Thread: EcmDroid

    by lowkey
    Replies
    22
    Views
    592

    Silencer as in a muffler? No need to do anything...

    Silencer as in a muffler? No need to do anything TPS related, if you had a stock muffler before with the exhaust valve (XB12) you will want to disable the valve using ECMDroid so you don't have the...
  21. Thread: EcmDroid

    by lowkey
    Replies
    22
    Views
    592

    The bigger question is why you have to reset the...

    The bigger question is why you have to reset the TPS? Contrary to popular belief it is NOT a cure all and doesn't need to be done much if at all. You would want to do it if you took the throttle body...
  22. Thread: EcmDroid

    by lowkey
    Replies
    22
    Views
    592

    For TPS reading, select "data channels" then on...

    For TPS reading, select "data channels" then on one of the down arrows select TPS (been a while since I've used ECMDroid but I believe the reading is in degrees) Make sure you are getting live...
  23. Replies
    1,315
    Views
    99,635

    Cleared some old messages out, thanks.

    Cleared some old messages out, thanks.
  24. Replies
    1,315
    Views
    99,635

    Thanks for the kind words 34nineteen!:up: I did...

    Thanks for the kind words 34nineteen!:up: I did hear back about starting a PT job yesterday (in Bullhead) so things are on the up. I still love the bike and don't want to part with it but I'm in...
  25. Replies
    1,315
    Views
    99,635

    Link isn't working on my phone but I do have it...

    Link isn't working on my phone but I do have it on CL so yeah probably. I'm jobless at the moment and have bills stacking up along with separating with the wife. I may have a job opportunity in CA in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4