Page 3 of 3 FirstFirst 123
Results 21 to 26 of 26

Thread: ecm spy loading maps?

  1. #21
    I'm in the same boat MAtteson.

    1125CR and can't find a race map to load up as a starting point.

  2. #22
    Junior Member
    Join Date
    Nov 2013
    Posts
    1
    Hello,

    My first post over here.
    I have a uly 2008.
    Somebody had success with the maps on https://sites.google.com/site/ecmspy/xb12/2008?

    I'm trying to figure out why my idle rev is ca 1500rpm and not 1050rpm.
    Sometimes i got also an hickup when pulling gas from idle.

    Done:
    -replaced stock exhaust with sebring open exhaust
    -k&n filter
    -breather reroute

  3. #23
    I dug this thread up trying to find out how to load maps and where to find maps to load and try out. I tried the maps from the ecmspy link above. The one Uly map won't load (it's BUEGB and my ECM is BUEIB) but the two 2006 BUEIB maps give me the following error:

  4. #24
    Junior Member
    Join Date
    Jul 2016
    Posts
    16
    Your idle is set incorrectly than. There is an idle screw located between the left scoop and engine (believe 09 models no longer have screw). See this thread - http://www.buellxb.com/forum/showthr...justment-screw
    You also can do a TPS reset and adjust this via ECM. I'm no expert, just ideas where you can turn to. Google "Buell Ulysses adjusting Idle" to read up more. There is also a 1400rpm cold idle and a 1100rpm warm idle, maybe that's what you're seeing at first?

    My 2008 XB12X also hickups at low rpm (1100-2000) when initially pulling on gas, especially if the bike is not fully warmed up. From my research the bike was adjusted to run lean in low RPMs to stick within government regulations. Flashing a race ECM or adjusting the fuel tables will fix this.

    Quote Originally Posted by Sikk View Post
    Hello,

    My first post over here.
    I have a uly 2008.
    Somebody had success with the maps on https://sites.google.com/site/ecmspy/xb12/2008?

    I'm trying to figure out why my idle rev is ca 1500rpm and not 1050rpm.
    Sometimes i got also an hickup when pulling gas from idle.

    Done:
    -replaced stock exhaust with sebring open exhaust
    -k&n filter
    -breather reroute

  5. #25
    Senior Member Chicknstripn's Avatar
    Join Date
    Aug 2014
    Location
    High Point, NC
    Posts
    2,144
    Check the date on the post you're replying to.
    It's over 3yrs old.

    Happens to the best of us

  6. #26
    Junior Member
    Join Date
    Jul 2016
    Posts
    16
    Quote Originally Posted by Chicknstripn View Post
    Check the date on the post you're replying to.
    It's over 3yrs old.

    Happens to the best of us
    Yea I noticed right after posting. Figured I'd leave that info there incase someone's researching the same problem... 8)



Page 3 of 3 FirstFirst 123

Similar Threads

  1. loading mounts to ecm
    By rsexauer in forum Buell Ulysses XB12x
    Replies: 4
    Last Post: 02-04-2014, 04:07 PM
  2. ECM failure after loading a diff race map
    By DiRTeNtwisted in forum Troubleshooting
    Replies: 16
    Last Post: 09-26-2013, 03:42 AM
  3. Fuel Map? Found something while loading race maps!!
    By theMelvster6 in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 9
    Last Post: 07-19-2012, 08:15 PM
  4. Anybody with an 03 actually notice a difference after loading a race map?
    By upthemaiden in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 12
    Last Post: 03-12-2011, 07:51 PM
  5. Anyone have trouble loading the 03 xb9 race map?
    By upthemaiden in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 15
    Last Post: 09-18-2010, 07:36 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •