Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 31

Thread: White wire mod messed it up! I think?

  1. #11
    Senior Member
    Join Date
    Jan 2011
    Posts
    424
    I'm not in professional mode. I was in standard. And Learn in ride? I don't know what you are talking about.

  2. #12
    Senior Member
    Join Date
    Nov 2010
    Posts
    5,416
    Try professional mode, maybe then you can disable the white wire in ecmspy.

    Then hook the wire you messed with back up, do another tps reset, and the learn in ride. There is a procedure to the reset, look up the DIY video on this site, it describes exactly what to do. I suck at searching on this site, maybe someone else can post a link for you.

  3. #13
    Senior Member
    Join Date
    Jan 2011
    Posts
    424
    I know how to do the tps reset. I've done it numerous times in the past couple days. I went through all the modes to see if the box became ungrey. But it didn't. Not in professional not expert. None of them. And what is learn in ride? And I replaced the wire already. Still the same problem. It is also running rich. Real rich. A flame shot out of the muffler last night.

    BuellSki

  4. #14
    Senior Member
    Join Date
    Nov 2010
    Posts
    5,416
    Learn in ride is part of the tps reset. I believe the DIY video explains it, maybe I'm wrong though. Basically ride easy, no quick throttle snapping, and stay at like 1/4 throttle. Don't wind it up. Just cruise for like 20 minutes.

  5. #15
    Senior Member
    Join Date
    Jan 2011
    Posts
    424
    What does that do?

  6. #16
    Senior Member
    Join Date
    Nov 2010
    Posts
    5,416
    Allows the ecm to learn the settings.

  7. #17
    Senior Member
    Join Date
    Jan 2011
    Posts
    424
    Ok. But if it's only idling for 30 seconds at most now. I can't ride it. I don't know what happened to it. The first tps reset I did I forgot to find 0 first. Then I finally found it. And I set it back to the 5.1-5.5 percent and it's doing this. I've tried turning it up to 5.9 all the way up to 7.3. That high it just kept reving all the way up to 25k then dropped back down to 1k. So I turned it back down to 5.5 and that dropped the revs down to 800ish and stalled. It sounded like it bogged down too low.

  8. #18
    Senior Member
    Join Date
    Nov 2010
    Posts
    5,416
    Where are you located?

    I know you said you know how to do the TPS reset but are you sure? Have you watched the DIY video?

    Explain exactly what you did. Sounds like you just did something wrong with the reset.

  9. #19
    Senior Member
    Join Date
    Jan 2011
    Posts
    424
    I'm in Newport news Virginia. I'll watch them tonight. I'm at work till midnight I'll post up my results when I get off work.

  10. #20
    Senior Member
    Join Date
    Aug 2008
    Posts
    5,146
    But if it's only idling for 30 seconds at most now. I can't ride it.
    You still should be able to ride it at a steady RPM (2500-3500); regardless of Idle.

    "Learn-in" ride is when the ECM goes into closed loop (monitoring) mode - Taking a long ride holding at a steady speed & RPM just gives the ECM more data to adjust values with more accurately. Also, check your plugs if you haven't in awhile.



Page 2 of 4 FirstFirst 1234 LastLast

Similar Threads

  1. 2009 xb9s white wire mod
    By Aceinthesky in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 4
    Last Post: 05-06-2015, 02:40 PM
  2. Anyone removed on the VSS White Wire on a 2009 and later XB12? (White Wire Mod)
    By LBoltUK in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 12
    Last Post: 06-25-2013, 08:21 AM
  3. Buell XB9 white wire
    By 06xb9r in forum Buell Firebolt XB12, XB9
    Replies: 35
    Last Post: 10-27-2012, 09:34 AM
  4. White wire??
    By tasha1329 in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 11
    Last Post: 06-07-2009, 02:55 PM
  5. White wire mod.
    By Kole_DeWoody in forum Do-It-Yourself Buell Mods
    Replies: 2
    Last Post: 02-06-2009, 02:38 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •