-
Junior Member
Awesome, I'm looking forward to seeing the retrofit!
-
Senior Member
Today the angel eye's came in, but the projectors are stuck in customs..... Hopefully I will have them soon, because I can't wait to start retrofitting!
-
Senior Member
Ok, the fun stuff begins!
To make sure I have all the time and no stress, I bought a second hand headlight unit online. Because this one was in a less good state, I swapped the units. So right now my bike runs with the second hand unit, and I will alter the original one.
(btw, my new indicators also found their way to my home!)
IMG_6703.jpgIMG_6704.jpgIMG_6705.jpg
also, please use this "guide" at your own risk. If you not know what you're doing, please do not start with this guide
-
Senior Member
Let me start by saying you won't have to bake your headlight. I used my heatgun to make the glue go soft
IMG_6707.jpg
So first I made sure the headlight unit was secured at a piece of my desk, so it would be easier to handle it.
IMG_6706.jpg
After that, I choose a starting point and started heating it up. Do not point the heat to long at the same spot, but make it evenly hot.
When you've done this for 1 minute, you can start with a screwdriver to pull up the nodge, that holds the lens in place.
Than you can work your way round the unit and you will end up with this.
IMG_6708.jpg
-
Senior Member
when the reflector is of the housing, you will notice that the reflector and lens are still 1 piece. This can be separated with a small screwdriver, between the silver notch and the lens.
IMG_6709.jpg
At that point, the reflector and lens become separate.
Tot make the angel fit, and have a nicely spread light output, I used lampshades.
IMG_6710.jpg
It will look like this in on the lens.
IMG_6711.jpgIMG_6712.jpgIMG_6713.jpg
-
Senior Member
to make sure the shades are in the middle, I used some wooden pins found in the kitchen.
IMG_6714.jpg
I could then glue them in to their new place.
IMG_6715.jpg
-
Senior Member
And now that they are in place, I can lite them up!!!
DRL
IMG_6716.jpg
Indicator on to the left:
IMG_6717.jpg
Indicator on to the right:
IMG_6718.jpg
-
Senior Member
I couldn't get them perfect on the photo, but in reality they are super bright and the output is nicely spread. There is a real small electronic board in the wires which turns off the white and turns on the orange/yellow. When you turn off the indicator, 1 second later the white leds turn on again.
The projectors are now through customs and I can pick them up on Monday. I will try to start installing them in the upcoming days.
Let me know what you think!
Last edited by marcel; 04-30-2016 at 07:55 PM.
-
Junior Member
Man, looks like you have a great head start. I really like the idea to zip tie the housing to the vise, should be it alot easier like you said. Also dig the halo mounting, never seen that done but makes perfect sense in this retrofit.
Looking forward to progress pictures over the next week.
-
Senior Member
yep, the zip tie to the vise really made a difference. as a bonus you can also turn the housing upside down (by spinning the handle) so you can reach the bottom side
for now I have 1 learning point. I ordered these rings http://www.aliexpress.com/item/Doubl...355432593.html in 94mm (3.7 inch). I think it would be possible to install the 99mm (3.897 inch). I already had the 94mm rings, so I installed them, but maybe, in the future I will swapp the rings and shades, but I will see how this "project" goes.
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules