Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 39

Thread: Left-side Low-side :( ...looking for Lt Footpeg, Shift Lever, & Frame Pucks

  1. #21
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Posts
    2,078
    Dan,

    Check out this link. This assembly pictured is what I was referring to. There is another thread from azmidget going into detail on this as well.

    https://www.buellxb.com/forum/showth...al-replacement

  2. #22
    Senior Member
    Join Date
    Feb 2020
    Location
    Milwaukee and Illinois
    Posts
    104
    [ATTACH=CONFIG]1388620200701_124346.jpg
    I just finished printing my preliminary Frame Puck to verify fitment to the frame (starting w/ the good side first!) Fits well though I have a few immediate changes and plan to add the detail on the face to make it look more OEM. Not bad for a first run!
    Attached Images Attached Images

  3. #23
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Posts
    2,078
    I would make it wrap a little more around the back to help cover any dents in a damaged frame.

    I wonder what it would look like if you removed the "point" and had cover the weld in front of it?

    Looks really good, though!

  4. #24
    Senior Member
    Join Date
    Feb 2020
    Location
    Milwaukee and Illinois
    Posts
    104
    Quote Originally Posted by 34nineteen View Post
    I would make it wrap a little more around the back to help cover any dents in a damaged frame.

    I wonder what it would look like if you removed the "point" and had cover the weld in front of it?

    Looks really good, though!
    Hey 34nineteen, ya, I'm glad you mentioned that about the back radius (in front of the knee)...I kept looking at pictures and some appear to go over and others appear to stop short of that radius. I think I'll do that for the next run. As for that front weld, I like that idea, too, though that'll exceed my printable area on my 3D print bed so I'll keep it short for now. It is a great idea, though...welds are always a bit unsightly!

  5. #25
    Senior Member Cooter's Avatar
    Join Date
    Dec 2012
    Location
    Crawling up your skirt
    Posts
    8,048
    I could help with that? Mines 300x300x400? I have PLA in it now but getting Nylon for another project (EBR airbox Charcoal can delete).

    Did you just scan one or is there a file out there already?

  6. #26
    Senior Member
    Join Date
    Feb 2020
    Location
    Milwaukee and Illinois
    Posts
    104
    Hey Cooter,

    I'm starting from scratch by scanning my frame and modeling new puck geometry. I'm going to turn that "knee" radius a bit on my next version as 34nineteen suggested. I don't want to run it all the way up to the weld at this time, just going to keep it simple for now...though that's a good idea for another day I'm getting close on finishing my next version.

    I'm running a CR-10, it's 300 x 220 x 300. You might be close, for running up to that weld, but I'd have to take a look.

  7. #27
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Posts
    2,078
    I think TPEHAK did that on the other forum. I think I saw it in the knowledge vault section. I’m not up on cad software, so not sure it that will help or not.

  8. #28
    Senior Member Cooter's Avatar
    Join Date
    Dec 2012
    Location
    Crawling up your skirt
    Posts
    8,048
    I'm running a CR-10 as well! Didn't know they made different beds for the same printer.

    Thanks 34:19 I didn't know he did that. I'll look for it and maybe pump some out to have on hand for people that need them. I really appreciate what the other dude was doing but $200 is just silly.

  9. #29
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Posts
    2,078
    Quote Originally Posted by Cooter View Post
    I'm running a CR-10 as well! Didn't know they made different beds for the same printer.

    Thanks 34:19 I didn't know he did that. I'll look for it and maybe pump some out to have on hand for people that need them. I really appreciate what the other dude was doing but $200 is just silly.
    Unfortunately itís not that silly. He is going to want to make a little $$$ on it and so is the retailer. At the small volume he is likely doing compared to HD, his landed cost is likely about what Harleys MSRP is/was.

  10. #30
    Junior Member
    Join Date
    Jun 2011
    Location
    Bloomington, MN
    Posts
    23
    Did you find that footpeg? I just happen to have one in my parts bin from my long since sold XB12S (I too had a small lowside, but on the right side, had to test out the new brake lever, no I didn't see that patch of sand...). Shoot me a PM and we can work out the address/details.

    I never would have thought pineapple works on road rash... might have to try that, but in no rush to find out!



Page 3 of 4 FirstFirst 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •