Page 6 of 8 FirstFirst ... 45678 LastLast
Results 51 to 60 of 74

Thread: Xb12r isolator mount

  1. #51
    Senior Member Cooter's Avatar
    Join Date
    Dec 2012
    Location
    Crawling up your skirt
    Posts
    10,877
    Screen Shot 2021-02-26 at 3.38.13 PM.png
    Nice blue helmet.

  2. #52
    Senior Member
    Join Date
    May 2018
    Location
    Vancouver WA
    Posts
    376
    No one have a bad isolator???

    I need the aluminum bracket for the manufacture of the new one to verify the id/od press fit nearly ready to get these shipping. no sleve is okay rubber torn not what I need the party that comes up with the bad one gets a new bushing when the run starts and I'll also have a poly "washer" to go between the bolt and isolator available for those of you that don't need a new one yet but would like to extend the life of your original part!

    Call or text me to make arrangements to ship if you have one.


    Thanks , CV 360-601-0597
    Last edited by cvc; 03-19-2021 at 12:43 AM.

  3. #53
    Senior Member outthere's Avatar
    Join Date
    Jun 2018
    Posts
    657
    Quote Originally Posted by cvc View Post
    No one have a bad isolator???

    I need the aluminum bracket for the manufacture of the new one to verify the id/od press fit nearly ready to get these shipping. no sleve is okay rubber torn not what I need the party that comes up with the bad one gets a new bushing when the run starts and I'll also have a poly "washer" to go between the bolt and isolator available for those of you that don't need a new one yet but would like to extend the life of your original part!

    Call or text me to make arrangements to ship if you have one.


    Thanks , CV 360-601-0597
    I have one I can send. It's not a failed part but I have an extra I can use. get in touch

  4. #54
    Senior Member
    Join Date
    May 2018
    Location
    Vancouver WA
    Posts
    376
    Quote Originally Posted by outthere View Post
    I have one I can send. It's not a failed part but I have an extra I can use. get in touch
    call me ill text the address

  5. #55
    Senior Member outthere's Avatar
    Join Date
    Jun 2018
    Posts
    657
    No phone here. mikekane@hughes.net is your best bet.

  6. #56
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Location
    Kolache Factory
    Posts
    4,424
    I *think* I may have one also. I have a new spare, and I think I have a used, but good one in my garage in a pile of parts. I have no idea where to even start looking as my garage has 3 disassembled Buells in it at the moment, and I'm losing my mind over the chaos.

  7. #57
    Senior Member
    Join Date
    May 2018
    Location
    Vancouver WA
    Posts
    376
    Quote Originally Posted by outthere View Post
    No phone here. mikekane@hughes.net is your best bet.
    PM and email sent

  8. #58
    Senior Member
    Join Date
    May 2018
    Location
    Vancouver WA
    Posts
    376
    Quote Originally Posted by outthere View Post
    I have one I can send. It's not a failed part but I have an extra I can use. get in touch
    Hey thanks! For getting the old one in the mail.

    I'm replying here as well so others Know the project is moving forward.
    Last edited by cvc; 03-26-2021 at 09:05 PM. Reason: add

  9. #59
    Junior Member
    Join Date
    May 2023
    Posts
    5
    Hey all, new to the site! Just picked up an 06 12Ss and low and behold the isolator isn't looking too hot. All of my searches brought me here.

    Have any of you tried the Twin Motorcycles press-in deal from the Nederlands?

    I see cvc has been in progress for a couple of years for a polyurethane press-in, but no updates or sales made yet to my understanding?? I'll happily be a guinea pig if there's one to send!

  10. #60
    Senior Member 34nineteen's Avatar
    Join Date
    Mar 2015
    Location
    Kolache Factory
    Posts
    4,424
    Quote Originally Posted by BlackMist View Post
    Hey all, new to the site! Just picked up an 06 12Ss and low and behold the isolator isn't looking too hot. All of my searches brought me here.

    Have any of you tried the Twin Motorcycles press-in deal from the Nederlands?

    I see cvc has been in progress for a couple of years for a polyurethane press-in, but no updates or sales made yet to my understanding?? I'll happily be a guinea pig if there's one to send!
    New OEM ones are still available.



Page 6 of 8 FirstFirst ... 45678 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •