Results 1 to 8 of 8

Thread: Rear 02 sensor error

  1. #1

    Rear 02 sensor error

    Hi guys.
    '06 XB9SX, 80000km.
    On my way home last night , and again on my way to work this morning, the CEL came on for
    about 5 km, then went off. Bueltooth showed a stored rear 02 sensor error. Is this likely
    a component failure in process, or should I be looking at a possible wiring issue ?
    Thanks.

  2. #2
    Senior Member Barrett's Avatar
    Join Date
    Jun 2020
    Location
    AmishLand, PA
    Posts
    387
    Quote Originally Posted by Beebop View Post
    Hi guys.
    '06 XB9SX, 80000km.
    On my way home last night , and again on my way to work this morning, the CEL came on for
    about 5 km, then went off. Bueltooth showed a stored rear 02 sensor error. Is this likely
    a component failure in process, or should I be looking at a possible wiring issue ?
    Thanks.
    Is this likely
    a component failure in process


    Possible...but not always.

    The ECM is seeing sensor values it doesn't like....hence the intermittent CEL.
    1-Wildly fluctuating engine temp signal being sent to ECM can cause this. Check ETS connector for condition and ETS harness for chafing. Historically, a known problem.
    2-Ground is being interrupted somewhere. Check them all and in particular, the ECM grounds.
    3-You FAILED to mention rideability issues, or lack thereof. If active CEL immediately preceded by cooling fan activation...it is always a failed ECM ground.
    4-This condition is typically NOT a failing O2 sensor or intake seals. NO mention of AFV value during this horrific experience. TPS reset 10% of the time will resolve this. Worth mentioning.

  3. #3
    Thanks Barrett.
    If I didnt see the CEL , I wouldnt have known it happened, so no performance issues of any sort.
    My AFV has always been within 10% of 100, but I did not check that specifically, will do so if
    it happens again. I did have the ground under the seat off earlier this week, I will check if that
    maybe is an issue.
    Cheers

  4. #4
    Senior Member Barrett's Avatar
    Join Date
    Jun 2020
    Location
    AmishLand, PA
    Posts
    387
    My pleasure. And think about running a single dedicated ground wire from the rear-most coil bracket mounting bolt to the negative battery cable attachment point on the subframe.....NOT to the negative battery terminal. 16-20 gauge works fine. Often times solves these dilemmas and rideability/ECM issues.

  5. #5
    Well I didnt get a chance to check yesterday, but the trip home gave no CEL.
    Hopefully the weekend will give me more time.

  6. #6
    ok so this morning I made some time to look at it.
    Pulled the entire airbox, checked cables for chafing , reseated everything
    I could access. Added a ground to the rear coilpack mount.
    Hooked up the Buelltooth and this is the readings.
    Oh and while I was at it, I did a TPS reset.
    Attached Images Attached Images

  7. #7
    Senior Member Cooter's Avatar
    Join Date
    Dec 2012
    Location
    Crawling up your skirt
    Posts
    9,698
    All I can see is that the AFV reading is telling the ECM to pull almost 20%(!!) of fuel from the entire map. An old or lazy O2 sensor can cause that (but that is a guess, not a diagnosis). You can check O2 running voltages under live data.

    The bike will run better if you re-set AFV to 100 and set the AFV limits to 90-110. Its not a "fix" though.

    If it's cheap enough for you to guess, the O2 is behind the cooling fan. Hang the rear of the bike, take off the seat, rear shock, and fan (the bottom slides towards you first and then out the bottom). It is possible to slip a 7/8" wrench under the frame to remove the O2, but a dedicated socket or crowsfoot on an extension is easier.

  8. #8
    Well the only thing I've noticed is a slight exhaust blow between the headers and the pipe. I'll tackle that the weekend and
    reset the AVF to 100 and see where it ends up. I can swing a spanner, but when it come to tuning and electronic brains, I
    get into deep waters. I appreciate everyone's assistance and patience.
    I do have my wife's 05 model which I can swap parts with if I need to , but access to the sensor makes that option
    lower down the list of things I want to do.
    Cheers



Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •