Page 1 of 2 12 LastLast
Results 1 to 10 of 22

Thread: XB12R Exhaust Header Mounting Studs

Hybrid View

  1. #1
    Senior Member
    Join Date
    Jul 2008
    Posts
    405
    My Beautiful Buell is out of commission... Help! :)

    So one of the studs that holds the front header into the exhaust port on the front cylinder has sheared off! I am in the process of drilling it out to use an extractor but so far it doesn't seem to want to budge! I know that drilling all the way to the bottom can help loosen it up so it'll come out, but I don't know how far the bottom of the stud is and I don't want to drill into the aluminum cylinder head. Does anyone know how deep the threaded holes for these stud go into the head?

  2. #2
    Senior Member GregoXB's Avatar
    Join Date
    Feb 2012
    Posts
    1,543
    I have to do this job. What's the consensus as to what is the best way to remove the broken header stud? I can see that EZ out is clearly a no.

  3. #3
    Senior Member GregoXB's Avatar
    Join Date
    Feb 2012
    Posts
    1,543
    Quote Originally Posted by lunaticfringe View Post
    with head on or off the motor?????????????
    Its the front stud. I was hoping to remove the headers and attempt the repair with the head on. No bueno?

  4. #4
    Senior Member Cooter's Avatar
    Join Date
    Dec 2012
    Location
    Crawling up your skirt
    Posts
    10,877
    The Jims tool. By far.

  5. #5
    Senior Member GregoXB's Avatar
    Join Date
    Feb 2012
    Posts
    1,543
    Quote Originally Posted by Cooter View Post
    The Jims tool. By far.
    http://www.jimsusa.com/pdf/instructi...ts/1705-IS.pdf This one?

    Any tips, tricks, pitfalls to watch out for? Any possibility of saving the original threads?

    The stud is flush with the engine, is it worth attempting to weld a nut to it?
    Last edited by GregoXB; 10-09-2018 at 09:38 PM.

  6. #6
    Senior Member konarider94's Avatar
    Join Date
    Sep 2009
    Posts
    4,435
    Quote Originally Posted by GregoXB View Post
    http://www.jimsusa.com/pdf/instructi...ts/1705-IS.pdf This one?

    Any tips, tricks, pitfalls to watch out for? Any possibility of saving the original threads?

    The stud is flush with the engine, is it worth attempting to weld a nut to it?
    With the Jims tool it is possible to save the original threads but not guaranteed. Dont start with anything smaller if you plan to use one. The tool is a guide and only works with the correct size drill bit. Otherwise it will likely follow any other pilot hole that will not be centered correctly. Only time i used one it was centered so perfect I drilled out the stud and was able to pull the threads from the stud out of the hole with pliers. The threads uncoiled like they were made out of a piece of wire. It couldnt have been any better if using a mill. My experience was a front stud with engine and head still in the bike.

    Id be tempted to try welding a nut to the stud but you might have to smooth it out with a grinder or flap wheel if it doesnt go well. Then you could revert back to a Jims tool.
    Last edited by konarider94; 10-10-2018 at 02:34 PM.

  7. #7
    Senior Member Silverrider's Avatar
    Join Date
    Sep 2016
    Posts
    2,790
    penetrating fluid , left handed drill bits.

  8. #8
    Inactive
    Join Date
    Feb 2011
    Location
    AmishLand, PA.
    Posts
    7,526
    Thank you Lunatic, I appreciate the tips. This is exactly what I was looking for. PaulPud is my go to guy for the big jobs. I won't be starting the job till this Saturday, so until then, I will be applying PB blaster on the regular.

    anytime greg. you know that. for a bit of clarity try what i've outlined if no access to jims' exhaust port tool. if you can borrow the tool then the procedure is different....what was mentioned above. paul's excellent and i'm sure he's done these before. happens frequently on XB's and older sportsters. if you were closer i'd just tell you to drop it off and i'd tackle it for you but sounds like you and paul have it covered. also greg when job is completed and you're remounting either stocker or hawkins or drummer muffler....you know...the ones in stock configuration and dimensions....carefully torque up the straps and CLOSELY CHECK the 2 bushings that attach front muffler mount to bottom of engine case. and on the muffler straps the FRONT STRAP threaded post MUST FACE THE LEFT SIDE OF BIKE...the REAR 2 STRAPS MUST FACE THE RIGHT SIDE OF BIKE.

  9. #9
    Senior Member
    Join Date
    May 2016
    Location
    Central Soviet state of new jersey.
    Posts
    2,674
    PB blaster comes to mind, if that don't work I do still have some top secret stuff you could try.

  10. #10
    Senior Member GregoXB's Avatar
    Join Date
    Feb 2012
    Posts
    1,543
    20181017_111913.jpg

    Bolts from Drummer SS MIA

Page 1 of 2 12 LastLast

Similar Threads

  1. Header studs?
    By aquaholic in forum Buell Firebolt XB12, XB9
    Replies: 6
    Last Post: 09-24-2014, 12:49 AM
  2. M2 exhaust header pipe mounting flanges
    By PJR7269 in forum Buell X1, M2, S3
    Replies: 0
    Last Post: 07-02-2014, 01:49 AM
  3. header studs
    By wolfo68 in forum General Motorcycle Chat
    Replies: 6
    Last Post: 01-26-2012, 07:56 AM
  4. header mounting stud
    By Farhan in forum Buell Lightning XB12S, XB12Ss, CityX, XB12Scg
    Replies: 4
    Last Post: 09-17-2011, 04:10 AM
  5. XB12R Exhaust header
    By airmanjwt in forum Buell Firebolt XB12, XB9
    Replies: 0
    Last Post: 07-10-2011, 02:34 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •